Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ezduzit

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    880

    Total length of mine, as pictured, from the left...

    Total length of mine, as pictured, from the left end of the collet closer to the right end of the collet nose is about 31"; 5-3/8" of that is what extends beyond the lathe's end cover.
    ...
  2. Replies
    26
    Views
    880

    This is the seller's eBay photo (colored red to...

    This is the seller's eBay photo (colored red to distinguish between his other models; the actual skates are black bodies). eBay seller "santschifarms". I paid $220 for a set of 4. Great seller.
    ...
  3. Replies
    26
    Views
    880

    Those bar hangars are on the back of mine. The...

    Those bar hangars are on the back of mine. The front looks like this.

    https://i.postimg.cc/sfcNgyjs/IMG-0399.jpg
  4. Replies
    26
    Views
    880

    Thanks. Always wondered what they were for when...

    Thanks. Always wondered what they were for when I've seen them on so many lathes.
  5. Replies
    26
    Views
    880

    It came with this JFK collet closer setup...

    It came with this JFK collet closer setup installed. But it does have the brackets on the back. And I only just now learned what needed to be done to allow the use of the D1-3 3-jaw chuck it came...
  6. Replies
    26
    Views
    880

    Got it. Figures that the ID of the drawbar...

    Got it. Figures that the ID of the drawbar prevents getting the knockout bar to contact the nose.
  7. Replies
    26
    Views
    880

    Duh! Thanks fellas. I really should have been all...

    Duh! Thanks fellas. I really should have been all over this. My bad. Was afraid to damage something in my ignorance.

    Is there any reason to remove the entire collet closing mechanism when using...
  8. Replies
    26
    Views
    880

    10 EE collet nose removal

    My new to me 1971 square dial has the pictured spindle arrangement. How do I remove the collet nose in order to install the D1-3 chuck?

    All comments welcome. Thanks fellas.
    ...
  9. A simple drill jig can be fabricated in the form...

    A simple drill jig can be fabricated in the form of a yoke with aligned holes drilled through both sides. Align the yoke's holes with the stock's existing holes and drill through from each side.
  10. Opportunity favors the bold.

    Opportunity favors the bold.
  11. He is correct.

    He is correct.
  12. Thread: WTB--die filer

    by ezduzit
    Replies
    11
    Views
    664

    Thanks to all who have contributed. The c/l...

    Thanks to all who have contributed.

    The c/l seller finally got back to me this morning and we hooked up this afternoon on his Milwaukee die filer. Missing the overarm. Runs quiet. May need some...
  13. Thread: WTB--die filer

    by ezduzit
    Replies
    11
    Views
    664

    Thanks fellas for the responses. Would prefer...

    Thanks fellas for the responses.

    Would prefer a benchtop unit.

    Had answered those local c/l ads, saying I would buy the Milwaukee and leaving my phone #, but received no reply.

    I will PM...
  14. Thread: WTB--die filer

    by ezduzit
    Replies
    11
    Views
    664

    WTB--die filer

    Looking for used die filing machine under $1,000. All comments welcome.
  15. In California, an individual can sue in small...

    In California, an individual can sue in small claims court, without an attorney, for up to $10,000. Other states may vary.
  16. When you have doubts... overcome them.

    When you have doubts... overcome them.
  17. Lots of ways to protect yourself: work off a...

    Lots of ways to protect yourself: work off a large deposit or retainer; get progress payments with sign-off at each stage; get payment in full before delivery, etc.

    Overcharging does nothing to...
  18. Replies
    17
    Views
    1,275

    The key is expendable. If you hammer it down,...

    The key is expendable. If you hammer it down, against the shaft, it could make the fit even tighter. Instead, drift it towards the bearing until it is exposed enough to get a good grip on it.
  19. Replies
    4
    Views
    794

    End mills arrived safely, as described. Thank you...

    End mills arrived safely, as described. Thank you for an easy transaction.
  20. Replies
    23
    Views
    1,421

    Appreciate all the comments fellas. Further...

    Appreciate all the comments fellas.

    Further research has advanced thus far. Oil distributors have not been any help. But the Okuma distributor "Gosiger", in Cypress, California, was able to kindly...
  21. Replies
    23
    Views
    1,421

    Thanks for the comments so far fellas. Really...

    Thanks for the comments so far fellas. Really don't want to make an arbitrary choice, like Vactra #2, just because I happen to have some. Still hoping to discover a true substitute for the turbine...
  22. Replies
    23
    Views
    1,421

    Turbine oil no. 90 ?

    What is it?

    The manual for my "new" Okuma LS lathe calls for the reservoir to be filled with 2.5-gallons of turbine oil no. 90. An internet search does not find it. Can anyone tell me what is the...
  23. Diamond lapping plate with part turning in lathe.

    Diamond lapping plate with part turning in lathe.
  24. Replies
    4
    Views
    794

    I'll take them. PM sent.

    I'll take them. PM sent.
  25. You should be able to drill just about any chuck...

    You should be able to drill just about any chuck to mount that way. O use the T-slots to hold it. Or a thin backing plate.
Results 1 to 25 of 432
Page 1 of 18 1 2 3 4