Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Booze Daily

Page 1 of 43 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    623

    I would suggest you only spot as big as the web...

    I would suggest you only spot as big as the web on that 5/8 drill or you'll be burning corners off your drill pretty quick.
  2. Replies
    1
    Views
    274

    I use one of these on my depth mics....

    I use one of these on my depth mics.
    https://www.mscdirect.com/product/details/52434321
  3. You get the side holes by rocking the tombstone...

    You get the side holes by rocking the tombstone +/- 90.

    Yeah, you're looking at sub 2 min cycle for 5k a month running one shift.
  4. I use this arrangement on my 4 axis mills. You...

    I use this arrangement on my 4 axis mills. You would get one part complete per cycle.

    266827
  5. Replies
    21
    Views
    1,414

    Could you just use duct tape? Otherwise, maybe...

    Could you just use duct tape?

    Otherwise, maybe just get some brass or copper shim stock and bend up your own.
  6. Not much gets by this bunch.

    Not much gets by this bunch.
  7. Replies
    32
    Views
    2,095

    This is as simple as it gets. Is there not a...

    This is as simple as it gets. Is there not a YouTube video you could watch?
  8. The taper attachment pushes the cross slide...

    The taper attachment pushes the cross slide toward you, so I always take the backlash out toward me. I also lock the compound down.

    I’ve only used a taper attachment a few times, so this is the...
  9. Replies
    26
    Views
    1,102

    I usually just fold up a small square of toilet...

    I usually just fold up a small square of toilet paper and use electrical tape.
  10. You need to take the backlash out the opposite...

    You need to take the backlash out the opposite way that you would think.
    IOW, overshoot your mark (smaller), then dial back to it.
  11. Replies
    16
    Views
    885

    That would be fun to watch for maybe, like, 3...

    That would be fun to watch for maybe, like, 3 minutes.
    And only if I just smoked a bunch of weed.
  12. I’ve made my own overlays before. You could make...

    I’ve made my own overlays before. You could make one to check the radius but you won’t be able to check to the center because even at 10X the center of the radius overlay won’t fit on the screen....
  13. That's pretty big feature for a comparator. ...

    That's pretty big feature for a comparator. You're not going to be able to use an overlay.
    You might have some luck by picking up 3 points on the radius and drawing it up on the computer.
    Fit your...
  14. Corrective Action Report/Request

    Corrective Action Report/Request
  15. Wow, 2-1/2 stock down to 1-7/16. 34" long? Good...

    Wow, 2-1/2 stock down to 1-7/16. 34" long?
    Good luck.

    I think I'd just buy a bar of 1-7/16 0-1 from McMaster and start there. $75 plus shipping.
  16. A quick Google search says Cr-Co is also called...

    A quick Google search says Cr-Co is also called Stellite. Yep, I've machined it with carbide.
  17. Are you still holding it with a steadyrest? If...

    Are you still holding it with a steadyrest? If so, take the steadyrest off. Does the center still run out .003?
    If yes, you have a bad center. If no, the run out will be transferred to the OD of...
  18. Hold down "Interlock" key and press "Machine...

    Hold down "Interlock" key and press "Machine Lock" key.
  19. Replies
    48
    Views
    3,658

    I've asked for qty discounts before. Sometimes...

    I've asked for qty discounts before. Sometimes they will, other times not.
  20. I've used Ohio Met in Elyria and Kowalski Heat...

    I've used Ohio Met in Elyria and Kowalski Heat Treating in Cleveland. You could give them a call.
  21. Replies
    110
    Views
    11,688

    This one? B&A Precision...

    This one?

    B&A Precision
  22. The rubber coupling is a Fernco fitting.

    The rubber coupling is a Fernco fitting.
  23. Replies
    49
    Views
    2,327

    What's it look like when you clean all that crap...

    What's it look like when you clean all that crap off?
    What's the major dia turned to? It looks like you have a sharp crest.
    I have an old 3M gray fiber wheel that I sawed a wedge out of that I...
  24. Replies
    9
    Views
    1,084

    So I should be good if I quit wearing my nipple...

    So I should be good if I quit wearing my nipple rings?
  25. Replies
    9
    Views
    1,084

    No real experience, but if they’re young enough I...

    No real experience, but if they’re young enough I would expect their skin is elastic enough that it would.

    All I know is I have a tan line and permanent indent from my wedding ring.
Results 1 to 25 of 1069
Page 1 of 43 1 2 3 4