Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: converterking

Page 1 of 55 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    360

    I used to have a Miller 350P like that. Welds as...

    I used to have a Miller 350P like that. Welds as good as my XMT304 with 22 wire feeder and runs on single phase.
  2. Replies
    51
    Views
    3,700

    I have been running a single buck-boost...

    I have been running a single buck-boost transformer to L1 for over 15 years. If you are running off your main panel, neutral and ground are bonded. Why don't you contact Phase Perfect to make sure?
  3. Machine a 12" x 18" x 12" piece of stainless on a...

    Machine a 12" x 18" x 12" piece of stainless on a machine that will fit thru a 34" door? Please take a video.
  4. How large and what material are the parts you...

    How large and what material are the parts you want to machine?
  5. Replies
    14
    Views
    1,048

    267307You could try some of this.

    267307You could try some of this.
  6. Replies
    51
    Views
    3,700

    And then the bad part, you have to check out....

    And then the bad part, you have to check out. Radio Shack "what is your phone number" , me "1-800-cash"
  7. Replies
    41
    Views
    3,148

    Gamer video cards are terrible for "shaded with...

    Gamer video cards are terrible for "shaded with edges" which I use all the time. I agree with ecc memory, I just had a stick of ddr4 fail
  8. Replies
    51
    Views
    3,700

    I never thought I would miss Radio Shack but the...

    I never thought I would miss Radio Shack but the convenience was nice. Electronic Supply by Industrial Electronics in Milwaukee Wisconsin : Potter Brumfield, Radio Shack Stores in Milwaukee ...
  9. Replies
    41
    Views
    3,148

    This re-seller has some interesting benchmarks....

    This re-seller has some interesting benchmarks. Recommended Workstations for SOLIDWORKS - Puget Systems
  10. Replies
    51
    Views
    3,700

    Your machine ran without a problem when you first...

    Your machine ran without a problem when you first brought it home? The high voltage most likely over stressed a component which caused your problem. So after you lower your incoming voltage your...
  11. Replies
    51
    Views
    3,700

    Buck and Boost Transformer Calculator - Schneider...

    Buck and Boost Transformer Calculator - Schneider Electric United States This should give you an idea of what you need. Federal Pacific Electrical Transformer SB24N1.5F Pri. 240x480 Sec. 24/48...
  12. Replies
    51
    Views
    3,700

    If you are using a Phase Perfect, use 1 buck...

    If you are using a Phase Perfect, use 1 buck boost transformer on the single phase input of the Phase Perfect. My single phase is usually around 247 volts and that is what i did to lower it.
  13. Replies
    7
    Views
    815

    It sounds like new features are going to Fusion ...

    It sounds like new features are going to Fusion
    Why no updates to Inventor Cam? - Autodesk Community
  14. Sticky: I hear Spinit laughing in the background.

    I hear Spinit laughing in the background.
  15. Replies
    61
    Views
    2,975

    Get a Phase Perfect.

    Get a Phase Perfect.
  16. Replies
    25
    Views
    1,588

    Buy a Miller XMT304 and a S22 wirefeeder. Runs on...

    Buy a Miller XMT304 and a S22 wirefeeder. Runs on single phase and makes beautiful welds. I have had mine for 15 years without a problem.
  17. ATI torque converter welders use one of these...

    ATI torque converter welders use one of these held stationary clamped around a rotating spindle. As long as you aren't turning it fast it should work good.TWECO 300 amp Copper Ground Clamp #92051130...
  18. Replies
    38
    Views
    3,734

    How much do you want for the pendant? I have a...

    How much do you want for the pendant? I have a friend looking for one.
  19. Before I hurt my back, I already had 2 Wesco...

    Before I hurt my back, I already had 2 Wesco peda-lifts and a Wesco manual counter balanced forklift. They still require force to use. Then I bought a Big Joe electric walk behind forklift. To me...
  20. My wife was a stay at home mom. When the kids...

    My wife was a stay at home mom. When the kids were in high school it was time for her to get a job. I design and manufacture parts for some of the fastest cars in the world. With various work holding...
  21. I too was tired of my high stress, high pay job....

    I too was tired of my high stress, high pay job. I sent my wife to school and she got a job with good benefits that covered me too. Jan 3, 1994 I quit my job and went out on my own. My goal was to do...
  22. Replies
    5,795
    Views
    166,761

    When I was in high school all the "not so cool"...

    When I was in high school all the "not so cool" kids listened to the Carpenters because their parents approved. I listened to Jimi Hendrix.
  23. Replies
    5,795
    Views
    166,761

    Do you watch Lawrence Welk?

    Do you watch Lawrence Welk?
  24. Replies
    62
    Views
    5,879

    How many 4,000 horsepower cars have you built?

    How many 4,000 horsepower cars have you built?
  25. Replies
    62
    Views
    5,879

    The lack of a standard is a huge problem. All...

    The lack of a standard is a huge problem. All manufacturers make a 1-1/4" pro mod input shaft. But half the time the torque converter hub doesn't fit the input spline. It is really neat when you pay...
Results 1 to 25 of 1368
Page 1 of 55 1 2 3 4