Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mllud22

Page 1 of 34 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    37
    Views
    1,836

    Sounds good.

    Sounds good.
  2. If you sand before painting its best to not sand...

    If you sand before painting its best to not sand the filler off the mill. Castings were a rough texture so they applied a layer of filler to smooth the casting. like bondo. It will never look the...
  3. With John's posting I.D. that it's A universal I...

    With John's posting I.D. that it's A universal I found this. If the pfd file in the first link isn't your mill you can look through the second link.
    Third link is a picture.
    ...
  4. There is a sub forum in the link below that you...

    There is a sub forum in the link below that you could post parts wanted. One other place to find parts like that is E-bay. You could try to find your motor local on Craig's List to save shipping...
  5. Shroud I haven't stopped thinking about those...

    Shroud
    I haven't stopped thinking about those cable guides either. The bottom of a stainless cup or container. I google stainless cups , dishes , ect....
  6. Replies
    12
    Views
    974

    Back in the days of those big switches you could...

    Back in the days of those big switches you could order a set of contacts and replace them. I use to set up machines that we did a lot of jogging during setup. When a relay started chattering we...
  7. Thread: 1911 Hendey

    by mllud22
    Replies
    6
    Views
    782

    266335266336266337266338266339 A little...

    266335266336266337266338266339

    A little bigger. I'm practicing making my pics larger. resized 150%

    Missed one:D
  8. Replies
    12
    Views
    974

    Your lathe was made in 1937. Go down the list of...

    Your lathe was made in 1937.
    Go down the list of serial numbers until you see where yours would fall in between higher and lower numbers.
    South Bend Lathe Serial Numbers
    When you can post...
  9. Replies
    12
    Views
    974

    If he returns with a serial number we could get...

    If he returns with a serial number we could get him narrowed down.
    He should be overwhelmed with reading material for a day or two. :)
    His first three phase could send him here....
  10. Replies
    12
    Views
    974

    Here are a couple publications submitted by Mike...

    Here are a couple publications submitted by Mike Lutz and Dennis Black to vintagemachinery.org
    .South Bend Lathe Works - Publication Reprints - South Bend Lathes Catalog 100B | VintageMachinery.org...
  11. Replies
    18
    Views
    1,933

    There are people that don't have any business...

    There are people that don't have any business touching a machine. You found one!
    Evidently someone had 150 grand to buy the machine but wont spend $100 on oil.
    I'll bet his daddy bought it for a...
  12. It looks great. You seem to be more experienced...

    It looks great. You seem to be more experienced than others on a first restoration. You do your homework.
    There appears to be a repair on the casting for the drive shaft in this picture. Right by...
  13. Thread: Thermite

    by mllud22
    Replies
    12
    Views
    1,979

    He was on the Briitex post on the 27th but hasn't...

    He was on the Briitex post on the 27th but hasn't posted much since the 6th.
    I also noticed him MIA
  14. Replies
    5
    Views
    661

    265807265808265807 Rare Myers Machine Co....

    265807265808265807
    Rare Myers Machine Co. Machinist Drill Press
    Rare Myers machine company drill press. See all the pictures. Best offer. Location is 18702 N. East PA265809
  15. Replies
    26
    Views
    3,462

    As the sixth hour bell rang on my last seconds of...

    As the sixth hour bell rang on my last seconds of high school on my final day I stuck my finger in the band saw. I didn't think the teacher seen me but as I walked past he said, you fckd up didn't...
  16. Replies
    25
    Views
    1,919

    This was a loaded question and I fell...

    This was a loaded question and I fell in.:rolleyes5:
  17. Replies
    25
    Views
    1,919

    My thinking is with the chuck holding the stock...

    My thinking is with the chuck holding the stock the headstock bearings are sharing the load. The headstock journal works as a lever along with the castings support.
    All the tailstock does is just...
  18. Replies
    25
    Views
    1,919

    I would think the live center would carry less...

    I would think the live center would carry less than half. The four jaw chuck carries more of the load. percentage ?
  19. Replies
    25
    Views
    1,919

    abom79 turning large materiall - Bing video...

    abom79 turning large materiall - Bing video

    I know of this utube guy [abom79] and forum member often turns similar sized shafts. I know he uses a monarch 60 series. Not sure if the lathe in the...
  20. Replies
    11
    Views
    1,064

    265411265412 For the curious after the add...

    265411265412

    For the curious after the add expires.
    Metal lathe - tools - by owner - sale


    Metal lathe - $275
    (Royal Oak,Md)

    The Flather Mfg Co 7 inch lathe. Good working order
  21. I didn't look at the price of that...

    I didn't look at the price of that cap.:rolleyes5:
  22. That setup in the photo was priced at $650.00 and...

    That setup in the photo was priced at $650.00 and it sold. I thought it was way over priced.
    I have all but the 90 deg. pusher. If you need any dimension's I could get that. mine is for a 36" so...
  23. Replies
    68
    Views
    6,108

    Pricey piece of bronze.

    Pricey piece of bronze.
  24. Replies
    40
    Views
    4,509

    It's better but why the staggered gussets at the...

    It's better but why the staggered gussets at the base. odd
  25. Replies
    29
    Views
    2,430

    It isn't any different. Sometimes if a lathe with...

    It isn't any different. Sometimes if a lathe with oil wicks sits for a long time it's hard to get oil flowing again
    The wicks in the apron are exposed to swarf ,chips and dust which oil works like...
Results 1 to 25 of 835
Page 1 of 34 1 2 3 4