Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jdd

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    487

    So, being a former Agie employee, I can tell you...

    So, being a former Agie employee, I can tell you that
    the detailed schematics for the DTR-50 are only held
    by a few and are held like state secrets. However,
    send me an email and I will respond...
  2. Replies
    5
    Views
    798

    peak current should be 64 average amps 50 or 60...

    peak current should be 64 average amps 50 or 60
    aco bitmask 63
  3. David, Have you changed Q value in technology...

    David,

    Have you changed Q value in technology
    from before?

    Jim
  4. Replies
    5
    Views
    798

    It sounds as though you know where to set these...

    It sounds as though you know where to set these options, but
    I will assume that you don't. When the machine is booting and
    is on the windows start page you must drag the cursor off the
    bottom of...
  5. David, have to check the schematics. will...

    David,

    have to check the schematics. will get back to you

    Jim
  6. Replies
    13
    Views
    1,401

    I could help you with some training over the...

    I could help you with some training over the phone
    if you like. Was formerly with Agie and worked with
    Rich back in the mid 90's. You can email me at
    [email protected]
  7. Replies
    13
    Views
    1,401

    The video card can be plugged into any of the PCI...

    The video card can be plugged into any of the PCI slots(smaller buss).
    Also this machine appears to be a Mondo Star. Does it have a mouse and
    mouse tray on the front of the machine? If so, it is a...
  8. the aluminum flex hose just directs the...

    the aluminum flex hose just directs the dielectric back into the reservoir.
    The positioning of it is not critical.
  9. david, I believe the valve yv22 is staying...

    david,

    I believe the valve yv22 is staying open when it should
    be closed. the line marked 220a is flushing pressure going
    to the lower head that yv22 controls. the valve may need
    replacement.
    ...
  10. Replies
    2
    Views
    394

    First of all, did you tap the internal...

    First of all, did you tap the internal tranformers for 480v?
    there are two tranformers. Secondly does this machine have a
    hand pendant? If yes, then make sure the estop on the hand
    pendant is not...
  11. Thread: AGIETRON 100C

    by jdd
    Replies
    6
    Views
    3,402

    Sorry, also you must have certain correction...

    Sorry, also you must have certain correction catalogs
    to run. for instance, 1000-0 piece.
  12. Thread: AGIETRON 100C

    by jdd
    Replies
    6
    Views
    3,402

    I am familiar with the machine. Need to see the ...

    I am familiar with the machine. Need to see the
    program and what is loaded into memory. you must
    have technology loaded first, then 3000, 3111,3222,
    3333, 3444 and then your program.
  13. How are you holding the workpiece? A magnetic...

    How are you holding the workpiece? A magnetic chuck holding
    the work can create havoc.
  14. Replies
    3
    Views
    864

    If you are using an M98 with Q then you should be...

    If you are using an M98 with Q then you should be using a G91(incremental)
    Also on the Taper Page the mode should be 11 and you should not use a
    G51/G52.
    Also the correct syntax is G01 X.4635...
  15. email me to discuss at [email protected]

    email me to discuss at [email protected]
  16. You encountered the errors when loading which CD,...

    You encountered the errors when loading which CD, OS2 or
    Agievision? Unfortunately, I do not have a PEC10 or SBC P5200.
  17. you have to be more specific when you say "VMI"....

    you have to be more specific when you say "VMI".
    Pec05 board? SBC board?
    Will it not boot?
  18. If you are sure your computer power supply is ok...

    If you are sure your computer power supply is ok and the monitor
    is good, the computer should boot to bios. If not, the motherboard
    is probably bad. Do all the lights on the hand pendant stay lit?...
  19. Replies
    2
    Views
    1,292

    is it a futura II or futura III?

    is it a futura II or futura III?
  20. Replies
    1
    Views
    1,979

    Is it lower gap box? If yes I can help. ...

    Is it lower gap box? If yes I can help.
    [email protected]
  21. Replies
    4
    Views
    2,759

    The E5 alarm is caused by one of two issues: 1)...

    The E5 alarm is caused by one of two issues: 1) Bad generator board. The GPM-50 board is in the lower rack of
    boards to the left of the SBC-02 board. This board should have three large LED's lit...
  22. Replies
    4
    Views
    2,759

    the mondo series sinkers use dc motors with...

    the mondo series sinkers use dc motors with rotary encoders to move the axes. The Pacer\Fine Interpolator
    boards handle the math that dictates how the motor/encoder moves. I have serviced these...
  23. Replies
    8
    Views
    4,058

    How much do you want for the sprint?

    How much do you want for the sprint?
Results 1 to 23 of 23