Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rke[pler

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    78
    Views
    11,290

    The thread chasing stop provides a positive stop...

    The thread chasing stop provides a positive stop for the cross slide dial. To set it just release the dial lock (on the face of the dial) and turn out at least 3 turn and then back in until the tool...
  2. Replies
    78
    Views
    11,290

    That's the hole for the thread chasing stop...

    That's the hole for the thread chasing stop screw, the pin is a retainer for the screw.
  3. Replies
    22
    Views
    1,260

    On the original topic: I never realized that the...

    On the original topic: I never realized that the bottom of that label had all that text. Just checked and my '56 has it as shown.

    On the current thread: never was a pilot. Did passenger for a...
  4. Replies
    3
    Views
    236

    I get a login page. Seems to work but I don't...

    I get a login page. Seems to work but I don't have an account to test.
  5. I'm pretty sure the thermal sensor is a fuse that...

    I'm pretty sure the thermal sensor is a fuse that opens when it's hot. So a short would be the normal state. If I recall correctly it's normally up on top of the DC panel cavity? Harry had to run...
  6. Here's an excerpt from the modular schematic...

    Here's an excerpt from the modular schematic showing the control circuit:

    http://www.kepler-eng.com/images/10ee_modular_elem.gif

    The power contactor is in the middle and all the switches are...
  7. I'd go with 4140 for the toughness.

    I'd go with 4140 for the toughness.
  8. Not really sure what sizes are a Vulcan #58 or...

    Not really sure what sizes are a Vulcan #58 or #56 is. I'd be interested in any of that hardware that takes 1/2" bolts
  9. Replies
    32
    Views
    3,067

    Looks like a neat project. I thought about...

    Looks like a neat project. I thought about getting one flame cut from steel, a castings would be a lot nicer. Put my name in.
  10. Replies
    6
    Views
    934

    I went through this some time ago, but for a step...

    I went through this some time ago, but for a step collet chuck mount with an integral 5C:
    Step collet chuck

    Only downside is that it's just cast iron and not hard. You'd want to be careful and...
  11. Replies
    5
    Views
    544

    From the '78 brochure, I don't have any other...

    From the '78 brochure, I don't have any other details:

    http://www.kepler-eng.com/images/10ee_infinitely_variable_feed.pnghttp://www.kepler-eng.com/images/10ee_electric_variable_feed.png

    (On...
  12. Replies
    3
    Views
    288

    Maybe provide some pictures with a rule in it for...

    Maybe provide some pictures with a rule in it for scale? Tehn folks might be able to help. Right now that pool is jus tthe folks with an 18CBB with that cap.
  13. Replies
    3
    Views
    288

    You mean one of the Gits cups? Oil Hole Cups...

    You mean one of the Gits cups?

    Oil Hole Cups and Covers | GITS Manufacturing
  14. Nice work!

    Nice work!
  15. Taper pin to pull it. You should be able to make...

    Taper pin to pull it. You should be able to make a replacement pretty easily.

    http://www.kepler-eng.com/images/10ee_tumbler_lever.gif



    Feed input into the gearbox. More likely one of the...
  16. Replies
    13
    Views
    963

    Nope, it came from Ingersoll Milling. A fellow...

    Nope, it came from Ingersoll Milling. A fellow who worked there saved it from being tipped into a recycle dumpster and stored it in his unattached garage. I rescued it from there and spent a fair...
  17. Replies
    13
    Views
    963

    I was there around then on a Family Day tour...

    I was there around then on a Family Day tour (every 5 years) and recall hearing one of the inspection folks talking about mapping the big surface plate and having to shut the parking lot so it was...
  18. Replies
    13
    Views
    963

    I retired from Sandia a few years ago as a...

    I retired from Sandia a few years ago as a contractor (worked for 9954 subbed to 5528 and others). Walked daily past the big old machining building west across from the primary standards building...
  19. Replies
    13
    Views
    963

    I've gotta wonder how a 10EE landed in Tucumcari....

    I've gotta wonder how a 10EE landed in Tucumcari. Maybe through Bentley's in Amarillo?
  20. Not neutral, just between forward/reverse feed...

    Not neutral, just between forward/reverse feed for threading. If you play with it you shouldn't be able to drop the half nuts in when you're in a feed position.
  21. You'll want to go through the process of tuning...

    You'll want to go through the process of tuning the drive. The procedure is listed in the manual and has likely been listed in some thread here, but let me know if you want the service sheets...
  22. Replies
    17
    Views
    924

    The system wants perhaps 20-25 PSI according to...

    The system wants perhaps 20-25 PSI according to this from Bijur (page 16):

    http://www.bijurdelimon.com/fileadmin/products/docs/bdius/Brochures/258_SYS_Single-Line-Resistance_BR.pdf

    That would...
  23. Replies
    7
    Views
    667

    Drawing EE-8-17 shows what seems to be a SHCS...

    Drawing EE-8-17 shows what seems to be a SHCS holding the back cover on. The last change date was 9/13/63 so certainly square dial.
  24. Replies
    7
    Views
    818

    I don't have one in front of me but I'd try...

    I don't have one in front of me but I'd try pulling the shaft the shifter arms are on out. That'd free up the arms and everything else would slide out. That's my recollection from 18 years ago...
  25. Replies
    9
    Views
    1,351

    Check the voltage on the field, bet you that it...

    Check the voltage on the field, bet you that it doesn't ever drop. That's how the motor gets above base speed. Lots of possible reasons, many depending on the drive type. Also have to ask: is the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4