Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Blazemaster

Page 1 of 27 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    62
    Views
    4,460

    I have a diesel 93' super duty (f450) with 12'x8'...

    I have a diesel 93' super duty (f450) with 12'x8' flatbed, air ride, telma retarder, banks turbo. It does pretty well but it's a little slow and there are times when I need a little bigger truck....
  2. Replies
    9
    Views
    827

    Looks like most of the parts are there, and some...

    Looks like most of the parts are there, and some nice extras. I also see some broken handles and by the looks of it they treated it like scrap when it was moved, also sitting in the rain. If people...
  3. Replies
    9
    Views
    731

    Yes. Spindle lever would not engage, and the oil...

    Yes. Spindle lever would not engage, and the oil was not flowing through the sight glass for the spindle/column. I still haven't had a minute to look at it closer.
  4. Replies
    9
    Views
    731

    Thanks for the replies. I am going to make...

    Thanks for the replies. I am going to make another go at it today, I was getting frustrated yesterday. I don't think it was the clutch but I will check it, and all the feeds/rapids worked. It's not...
  5. Replies
    9
    Views
    731

    Here are some pics 280688280689280690280691

    Here are some pics

    280688280689280690280691
  6. Replies
    9
    Views
    731

    K&T 2k column problems

    I have an old 2k that I could use for a job and it quit workin on me. Went to start it up one day and it wouldn't quite engage when you pulled the lever, felt like it was catching on something. I...
  7. Shizouka doesn't seem to be too hot of a topic on...

    Shizouka doesn't seem to be too hot of a topic on the forums and most of the threads I have seen are on the AN-S
  8. Replies
    20
    Views
    1,469

    You can drive taps with those Scully Jones split...

    You can drive taps with those Scully Jones split sleeve drivers, can find em on ebay cheap sometimes. Can also make something out of an old mt4 tool that gets no use/broken. Just drill a hole for the...
  9. Replies
    3
    Views
    572

    Well that didn't take long. Had about 30 calls...

    Well that didn't take long. Had about 30 calls since last night. Sold.
  10. Replies
    3
    Views
    572

    Here are some pics, hope they dont come out...

    Here are some pics, hope they dont come out upside down

    279876279877
  11. Replies
    3
    Views
    572

    Towmotor lt-35 1 ton forklift

    I have a 60's towmotor lt-35 forklift. It is rated to lift a ton, and goes 12 feet high. Propane powered, has been a good little starter lift for me. I picked up a larger lift, so this one has just...
  12. Replies
    13
    Views
    1,113

    Threw in a new coil and condenser today and it...

    Threw in a new coil and condenser today and it fired right up. Anyone wanna buy a tiny 1 ton lift?
  13. Replies
    13
    Views
    1,113

    Well I checked timing and that seems to be fine....

    Well I checked timing and that seems to be fine. At this point I am thinking it is a weak spark. Although it is blue, it doesn't seem to want to jump any type of gap.
  14. I'm not so sure I would have handled it...

    I'm not so sure I would have handled it differently. Pissed me off just reading it lol. Some people have no respect and can't take a hint.
  15. Replies
    13
    Views
    1,113

    Thanks for the replies. I will go ahead and check...

    Thanks for the replies. I will go ahead and check the timing tomorrow and verify spark again. I am smelling a little propane on startup, but it's because I have been holding the purge button open...
  16. Replies
    13
    Views
    1,113

    I put new plugs in it about 6 months ago when i...

    I put new plugs in it about 6 months ago when i did a tuneup. I will check the distrib key but I don't think that's it. Thanks
  17. Replies
    13
    Views
    1,113

    Forklift won't Start

    Here's a little back story. I recently picked up a new forklift and I have been getting ready to sell my old one. I've had the new one for a few months. I warmed up the old one and used it to change...
  18. Replies
    16
    Views
    1,183

    I have a wallace 15 ft span, 13ft tall, 3 ton...

    I have a wallace 15 ft span, 13ft tall, 3 ton crane that uses an s10x25.4. I have used it to load and unload lots of machines in the 3-6000lb range. I would imagine a s7x15.3 would be fine for...
  19. You are mistaking the word "better" for...

    You are mistaking the word "better" for "profitable".
  20. I love when people try to convince you to sell...

    I love when people try to convince you to sell off YOUR stuff for THEIR reasons. I'm guessing with 1000 horizontal cutters you won't know what you have until you store them properly, which is what...
  21. Replies
    4
    Views
    610

    Sure there are other machines that would make...

    Sure there are other machines that would make quicker work of it but if an M head is what you have and the part is within its travels it should be able to do that, just will take a bit longer.
  22. Replies
    38
    Views
    1,948

    I have a friend that is a butcher and he gave me...

    I have a friend that is a butcher and he gave me a stack of old butcher coats. They are white so they get dirty pretty easy but that's what they are there for
  23. Replies
    4
    Views
    516

    Well after fussing with it for an hour or so I...

    Well after fussing with it for an hour or so I finally figured it out. The manual makes it sound so simple but when they say move the table leftwards until you can see the threaded rings, you need a...
  24. Replies
    16
    Views
    1,358

    It looks like a nice little machine, but looks...

    It looks like a nice little machine, but looks well used and John Evans pointed out some downsides. I have never even heard of d5.
  25. Replies
    4
    Views
    757

    I see this a lot on craiglist. There is a guy...

    I see this a lot on craiglist. There is a guy around here that has been posting a bunch of machinist tools for years now. They are all nice tools in nice shape but at the prices they just aren't...
Results 1 to 25 of 665
Page 1 of 27 1 2 3 4