Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Lakeside53

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    3
    Views
    343

    yes, you could easily have enough movement in the...

    yes, you could easily have enough movement in the heads to cause such misalignment. Take them off... it will all be obvious when you try to assemble all there parts. Good time to check your valve...
  2. Replies
    10
    Views
    551

    ROC 02? WOW.... or do you mean 2002? ...

    ROC 02? WOW.... or do you mean 2002?


    No... you don't have to be member. Try going from here : Quincy Air Compressor Manuals | Quincy Compressor

    Go to instruction manuals, then "find a...
  3. Replies
    10
    Views
    551

    Did you order based on the nameplate ROC (Record...

    Did you order based on the nameplate ROC (Record of change)? Like vehicle VIN numbers, it's important to get the right parts. Do you have the parts manual?

    Here are all the manuals for...
  4. as ^^^^. Choosing high range gives about 50%...

    as ^^^^. Choosing high range gives about 50% hp at 1/2 mains frequency, which is the same as your original motor would have put out at that speed. Either leave as fully variable or wire one...
  5. After a wonderful day you're going home to a cute...

    After a wonderful day you're going home to a cute wife and you are going to snooze?
  6. yep, as above. Good guy to deal with - he'll...

    yep, as above. Good guy to deal with - he'll help you figure out the oddball types also.
  7. Send that all south. Still pissing down here.

    Send that all south. Still pissing down here.
  8. Replies
    19
    Views
    949

    The machine does not need ground to run; you...

    The machine does not need ground to run; you need ground to stay alive.

    If you have multiple machines, run it though a fused disconnect.
  9. Replies
    17
    Views
    1,367

    damn phone keyboard! At least someone reads my...

    damn phone keyboard! At least someone reads my posts :D:
  10. Replies
    5
    Views
    478

    Strong alkaline base is fine with Steel.

    Strong alkaline base is fine with Steel.
  11. Replies
    17
    Views
    1,367

    I have a 10 inch nice Swedish 3 jaw. D1-6 with...

    I have a 10 inch nice Swedish 3 jaw. D1-6 with only 3 pins direct mount into the chuck body. On the other hand I have a 6.25 Bison on a D1-6 backing plate - all 7 pins. lol.
  12. if 78 is too long just go shorter (obviously)....

    if 78 is too long just go shorter (obviously). Plenty of online calculator to tell you the difference in pulley to pulley spacing for belt lengths. Or simple math, or piece of string.

    Gates...
  13. Replies
    27
    Views
    2,018

    Barrel band heaters. They snap around 15, 30 or...

    Barrel band heaters. They snap around 15, 30 or 55 gallon barrels. With two bands we do about 50 gallons a week easily. Long shaft mixer (1/8th hp) in the top on a timer (5 min on, 15 off). Takes a...
  14. I'm part of this me-too-movement. To a fault. ...

    I'm part of this me-too-movement. To a fault. On the other hand, been doing it all my life and pretty damn good at most stuff now. Unfortunately I get to be the go-to-guy, at home, neighborhood,...
  15. Replies
    27
    Views
    2,018

    It works fine (in fact, very well), but you are...

    It works fine (in fact, very well), but you are flushing all the crap down the sewer... Can't do that around here. Check your local regs. And... look for one with a stainless steel interior. ...
  16. Yep... this is what we use at work (Torrit),...

    Yep... this is what we use at work (Torrit), except it' s 2x15hp motors! Runs about 50 grinding and polishing stations with plenty of additional vac for expansion (throttled back with a pair of...
  17. Check your RPC voltages as you start the...

    Check your RPC voltages as you start the generator. Good chance your generated leg is sagging causing high starting currents. Nothing wrong with correctly specified IEC contactors and overloads -...
  18. Probably your contactor. The contacts do wear...

    Probably your contactor. The contacts do wear out and on name brand types you can buy replacements. But yours is "new", so obviously... make sure the contactor is rated for the motor HP (not just...
  19. Replies
    11
    Views
    903

    Unless someone has really mucked with that...

    Unless someone has really mucked with that Maximat head, they use an E25 collet. If you replace the nose nut (many sources) you can use ER25 collets. You can also just buy another MT2 to ER25....
  20. Don't "glue" it on... If it comes off and jams...

    Don't "glue" it on... If it comes off and jams the motor at startup, you will be in far worse shape. Maybe mechanically fasten it but I wouldn't. The mass of the fan is so low in comparison to...
  21. Replies
    16
    Views
    1,629

    Check if any you know of locally that have a...

    Check if any you know of locally that have a taper attachment and take a couple of pics. Any other readers - love to see a pic of a Howa factory unit. Nobody around here has one, and it's one of...
  22. Replies
    16
    Views
    1,629

    Thank you for making my new year start well!

    Thank you for making my new year start well!
  23. Replies
    16
    Views
    1,629

    We'll likely have to build one... not hard, but...

    We'll likely have to build one... not hard, but making two would make it worthwhile. Seems like nobody ever lets their Howa's get parted out!
  24. Replies
    16
    Views
    1,629

    I really like to see details on a taper...

    I really like to see details on a taper attachment, and an illustrated parts list. Surely someone has those...
  25. Replies
    16
    Views
    1,629

    I also sent him one :) Anyone finding any other...

    I also sent him one :) Anyone finding any other Howa 850/1000/1500 documentation, I'd sure like it. Wonderful lathe.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4