Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BT Fabrication

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    760

    find someone who has one. other then that its a...

    find someone who has one.
    other then that its a ton of manual labor sanding/polishing
  2. Replies
    15
    Views
    335

    how was the motor tested? need HV tester, a...

    how was the motor tested? need HV tester, a digital multimeter won't pick up certain issues like this
    to me it sounds like a vibration that is causing a short/bad connection. wont see it unless...
  3. id agree with above, newer controllers come with...

    id agree with above, newer controllers come with a few more visual aids, but nothing per the controller side that stands out to justify the cost.
    work with what you have, they will learn more the...
  4. Harris is still a decent brand, is from a major...

    Harris is still a decent brand, is from a major supplier lincoln
    alcotec is best I have found so far.
  5. around here that is probably a $500 table at least

    around here that is probably a $500 table at least
  6. Replies
    2
    Views
    341

    And this is not going to go well, square tube...

    And this is not going to go well, square tube always likes to kink. look up JD2 and buy the bender and die for $1000
  7. As far as i understand it, you need to have a...

    As far as i understand it, you need to have a special skill set and a reason to move here. Might be good to inquire to the CBSA and see what is required for entry.
  8. Replies
    23
    Views
    1,491

    only way is un clamp and slide and re indicate it...

    only way is un clamp and slide and re indicate it in. or buy a big machine and ship it out there.
  9. Replies
    15
    Views
    795

    are you sure its not a deformed M10x1.25?

    are you sure its not a deformed M10x1.25?
  10. Replies
    9
    Views
    1,261

    that's what it would be doing, just getting into...

    that's what it would be doing, just getting into the USA and back is a problem ATM.
  11. yep, looks just fine to use. most likely wye...

    yep, looks just fine to use. most likely wye wound.
  12. Replies
    5
    Views
    292

    not a good idea, internal contactors are sized to...

    not a good idea, internal contactors are sized to current draw of a 15hp and not a 20hp.
  13. Replies
    28
    Views
    1,607

    make a single part with less depth and see what...

    make a single part with less depth and see what happens,internal stresses can find the weakest link and fracture.
  14. Replies
    17
    Views
    1,188

    in the pipe world, there is a thing, ususally...

    in the pipe world, there is a thing, ususally found at a welding supply shop. its called a pipe wrap for doing this exact thing. wrap, scribe a line and it has measurements on it also.

    and yes, go...
  15. yep, they are most available 1/2" and over, that...

    yep, they are most available 1/2" and over, that is where the drill bits start to require large hp to drive it. plus you are saving much more drilling 1" with a 1/8 thick annular cutter then the...
  16. Replies
    3
    Views
    234

    contact your local HFO for Haas. they can...

    contact your local HFO for Haas. they can instruct if you need to lock the column on it to move it and lifting points.
  17. call your local tow company with a rotator truck,...

    call your local tow company with a rotator truck, they do crane things all the time and not that expensive around here, like $150 an hr
  18. Replies
    11
    Views
    824

    what you are looking for is a face mill or fly...

    what you are looking for is a face mill or fly cutter, yes they are $, but its the cost of doing buisness
  19. you could always find a good but very expensive...

    you could always find a good but very expensive gun drill, either way that would be a few thousand just to source one from a tooling rep.
  20. a hougen is the best of the best. but for 7/16",...

    a hougen is the best of the best.
    but for 7/16", id go standard spiral unless its a massive plate.
    and yes, mag drills can get a regular jacobs chuck to use a regular drill but and not an expensive...
  21. whats " a long time"? people can be busy with...

    whats " a long time"? people can be busy with other things too....
  22. Replies
    6
    Views
    368

    why a wiring diagram, all the information is...

    why a wiring diagram, all the information is right there. if not knowing, find a local electrician, toss him 100 bucks and call it a day.
    that one is a 110V/220V pump. just run it off 110 like its...
  23. Replies
    20
    Views
    823

    those electrolitic caps are probably so old that...

    those electrolitic caps are probably so old that they no longer function as intended. basically just scrap.
  24. Replies
    13
    Views
    634

    got some for a friend of mine. plasma cutting on...

    got some for a friend of mine. plasma cutting on a table from 1" sheet. just need to buy a 2000lb sheet first.
  25. feed override till it breaks, then back it off 10%

    feed override till it breaks, then back it off 10%
Results 1 to 25 of 371
Page 1 of 15 1 2 3 4