Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Had a '51 Seagrave 906 CDI pumper a few years ago...

    Had a '51 Seagrave 906 CDI pumper a few years ago as one of my toys. About 3-4 MPG driven lightly ,muffler not required on fire trucks around here,talked pretty good on straight pipe.
    OX That was a...
  2. As for my moniker, I used to do dal rescue, when...

    As for my moniker, I used to do dal rescue, when you have 5 dals the neighbors start calling you names:)[/QUOTE]

    I too was into Dal rescue and for about 8 years I also had 5 or so Dals around...
  3. They were used to help keep the horses clam ,back...

    They were used to help keep the horses clam ,back when things were horse drawn. And by the way I had a round dozen Dals from the late 90s til the last one past in '16 and not a one was deaf!! Some of...
  4. You really screwed the pooch here,most likely...

    You really screwed the pooch here,most likely that sleeve was not designed to be removed from the pulley. You have 2 choices here as I see it make a replacement of scrap that drill press. That cheap...
  5. Replies
    0
    Views
    313

    Carbide insert lathe tooling & inserts

    Been going through my lathe tooling trying to consolidate insert types/styles and these are excess.
    Right hand turning tool 1/2 shank and 8" long 5/8 shank boring bar CPMT 3XX insert style + over 80...
  6. Taper attachment-mic carriage stop big pluses....

    Taper attachment-mic carriage stop big pluses. Down side no QC box ,be sure there are the gears for it there. As said look for missing teeth on the back gears. L model = Heavy 10 ++++ Be a great...
  7. Replies
    8
    Views
    746

    I have a assortment of NSK stuff and as said damm...

    I have a assortment of NSK stuff and as said damm good,but not quite B&S or Mitutoyo .
  8. Replies
    4
    Views
    515

    Looks like a good paper weight!

    Looks like a good paper weight!
  9. Replies
    3
    Views
    386

    Take a look at a "TPG" 3XX or TPGB " box lable is...

    Take a look at a "TPG" 3XX or TPGB " box lable is shot,hard to read.
    Also try this linkhttp://www.carbidedepot.com/formulas-insert-d.htm
  10. Here in Phoenix with the limited tooling...

    Here in Phoenix with the limited tooling $1200-1800. Your area probably 800-100.
  11. Replies
    32
    Views
    1,419

    Easier yet bring the dogs in the house !

    Easier yet bring the dogs in the house !
  12. Replies
    26
    Views
    1,466

    Legal size Priority envelopes are also flat rate...

    Legal size Priority envelopes are also flat rate a bit more like .50 or so. I use them on occasion.
  13. Try tightening the 2 screws in the side of the...

    Try tightening the 2 screws in the side of the can ring. AFTER FIRST loosening the little locking screws. No one ever seems to lube that area and the ring will sooner or later wear into the...
  14. Pull the quill out of the TS and use a long drift...

    Pull the quill out of the TS and use a long drift .
  15. Replies
    9
    Views
    820

    I'll bet you $5 that they don't use base /clear !...

    I'll bet you $5 that they don't use base /clear ! Most likely a pressure pot/remote gun for production painting. Base/clear is a car makers rip off ,goes to shit in a few years . Cheaper to buy a new...
  16. Replies
    0
    Views
    224

    FS CPMT 3XX carbide inserts

    Sorting through things on a lazy Sunday and found a mixed bunch of new and used CPMT 3 series inserts. Funny thing is I do not have any holders to use these. As I said some new and all the used seem...
  17. That ONLY works with keyed style chucks!

    That ONLY works with keyed style chucks!
  18. Too big a tip? filler size? Tip size #1 3/32...

    Too big a tip? filler size? Tip size #1 3/32 filler. Not all that bad but to me too much heat,fillet weld like that is one of the hardest to do.
  19. From the looks of that A arm more like a complete...

    From the looks of that A arm more like a complete new one would be in order. But as above weld in a repair taper sleeve. Fabricated piece with broken welds Sheesh !
  20. Replies
    15
    Views
    1,551

    Interesting ! spindle OD is smaller than I would...

    Interesting ! spindle OD is smaller than I would expect. Anyway lathe looks very nice,have fun.
  21. Replies
    15
    Views
    1,551

    And the question is ? What does that bloody great...

    And the question is ? What does that bloody great hole in the end of the spindle measure ? Looks to be 1-3/8s + .IF so someone has put a Heavy 10 spindle in this lathe,which is great!
  22. Replies
    16
    Views
    1,337

    Looks like a CNCed plain old semi-useless...

    Looks like a CNCed plain old semi-useless drill/mill to me. You can not make a silk purse out of a sows ear. Have the seller run a program on it,see how accurate/usuable it is/ain't.
  23. Any chance of putting a Heli-Coil in that plate ?...

    Any chance of putting a Heli-Coil in that plate ? Very nice work !
  24. Replies
    2
    Views
    597

    2-J vari speed head looks like 42" table ,mid 70s...

    2-J vari speed head looks like 42" table ,mid 70s or earlier with the door in the column.
  25. If you want to make things buy the Le Blond ! If...

    If you want to make things buy the Le Blond ! If you want a long term project get the 10EE. A few years ago a local dealer had a VFD repowered 10EE and he had a hard time selling it. With the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4