Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: lionelt

Page 1 of 43 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    22
    Views
    1,656

    Are these clear enough? Rear one without the...

    Are these clear enough?

    Rear one without the vent has dropped edges like a tin lid.





    329851
  2. Replies
    7
    Views
    693

    Was that your reply on other site with the photo?...

    Was that your reply on other site with the photo? Maybe post it here, should this post come up in a search in the future.
  3. Replies
    7
    Views
    693

    There is an answer on the other site that says to...

    There is an answer on the other site that says to leave the allen key in for leverage and twist the opposite end to unscrew.

    Photo of attachment as well showing the parts.
  4. One like this? PEC Tools 7116-024 16R 24" 4...

    One like this?

    PEC Tools 7116-024 16R 24" 4 Piece Combination Square Set, reads 32nds, 64ths, 50ths, 100ths.
  5. Replies
    21
    Views
    1,896

    Nice to get a follow up on posts like this. ...

    Nice to get a follow up on posts like this.

    Interested in the follow up on inserts. I am getting birds nests but not a big problem as not turning a lot of aluminium.
  6. If Amal do not get back to you, try contacting...

    If Amal do not get back to you, try contacting the Sammy Miller Museum.


    Sammy Miller Museum | Contact Us


    The have rebuild rare motorcycles for years, and have ways to find hard to find...
  7. Replies
    10
    Views
    1,270

    Peter Stubbs factory. Closure threat for one...

    Peter Stubbs factory.

    Closure threat for one of Warrington's oldest companies
  8. Replies
    10
    Views
    1,270

    British Museum may be able to identify the...

    British Museum may be able to identify the painting.


    Collections Search | British Museum

    Collections Online | British Museum


    Edit - to add this..
  9. Thread: Big Vise

    by lionelt
    Replies
    7
    Views
    1,665

    Here’s one. Not close to you though. Reed...

    Here’s one.

    Not close to you though.

    Reed 8” Model 208 Swivel Vise with base. - tools - by owner - sale
  10. Replies
    13
    Views
    1,420

    Put the tube in lathe chuck, inside another tube...

    Put the tube in lathe chuck, inside another tube for protection, put small disk with pins for the cap holes in tailstock chuck, unwind by turning lathe chuck by hand.
  11. Would one of these work to get two tools in one...

    Would one of these work to get two tools in one turret position?

    VDI30 FORM A1 BLANK L= 85 mm


    https://www.toolholdershop.com/images/large/VDI%20Boring%20Bar%20Holder-430.jpg
  12. Replies
    20
    Views
    3,351

    They use suction cups in the packaging and...

    They use suction cups in the packaging and printing industry, that could be a source for different cup styles.
  13. Replies
    47
    Views
    10,738

    Dovetail jaws I mark to use again. ...

    Dovetail jaws I mark to use again.




    328302


    328303
  14. Replies
    153
    Views
    10,198

    Two Prototrax using the conversational, or import...

    Two Prototrax using the conversational, or import dxf using their offline programming.

    Emco Turning Centre live tooling with C axis, programmed on the machine with G code.

    Have CadCam, not...
  15. Replies
    12
    Views
    1,433

    Looking at chart here you can see how confusion...

    Looking at chart here you can see how confusion can arise when quoting nominal metric equivalent.

    Dimension Table for T-Slots, Bolts, and Nuts Table Chart | Engineers Edge
  16. Replies
    1
    Views
    268

    See if this would help. G-Wizard Editor:...

    See if this would help.

    G-Wizard Editor: Check, Optimize, and Learn G-Code Easily - CNCCookbook: Be A Better CNC'er
  17. Replies
    17
    Views
    1,348

    Maybe that was the reason the stop pin is in the...

    Maybe that was the reason the stop pin is in the tool changer now, to prevent accidents?
  18. Have a Stanley knife blade to slide over area to...

    Have a Stanley knife blade to slide over area to remove splinters, get the direction right they pull out, if that doesn’t work cut a bit of skin away with nail clippers.
  19. Replies
    10
    Views
    1,270

    Don Plato Auction House, great find.

    Don Plato Auction House, great find.
  20. Replies
    14
    Views
    1,006

    You can buy square brushes for duct cleanng. ...

    You can buy square brushes for duct cleanng.

    Here’s a random search.

    Duct Cleaning Brush Products for Facilities Management
  21. Replies
    0
    Views
    366

    Wazer Waterjet Cutter

    Anyone familiar with the Wazer Waterjet Cutter?

    This arrived in my in box earlier today a message from a mailing list.

    Wazer | Water Jet Cutter | - Trusted Brands | Solid Print3D

    I have had...
  22. Replies
    22
    Views
    1,656

    The TMX software on the machine can be downloaded...

    The TMX software on the machine can be downloaded for offl line programming from Southwestern Industries that version is free to download I believe. This does tool-path simulation as wire frame. The...
  23. Replies
    78
    Views
    5,577

    327572 Yes four T slots. You can save X Y...

    327572

    Yes four T slots.

    You can save X Y coordinate location relative to bottom left corner ball lock.

    I have not used a plate and ball locks, as I understand it, there are two liners you...
  24. Replies
    78
    Views
    5,577

    This is what I was recommended when I bought my...

    This is what I was recommended when I bought my machine.

    The block being squared up is mild steel with tooling shown.


    327545327546327547

    327548
  25. Replies
    22
    Views
    1,656

    This shows how short vice has to be.

    This shows how short vice has to be.
Results 1 to 25 of 1061
Page 1 of 43 1 2 3 4