Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: lowCountryCamo

Page 1 of 60 1 2 3 4

Search: Search took 0.07 seconds.

  1. I sent email Friday to a small Vent manufacture...

    I sent email Friday to a small Vent manufacture Airon offering to make parts. I would do it for no charge if I could. Have not heard anything yet
  2. I know I have seen a picture of the signal wave...

    I know I have seen a picture of the signal wave but cannot find it now. Here is the encoder and pinout. I do not believe it is a serial encoder. Fanuc calls it an incremental pulse...
  3. Testing incremental encoder with oscope

    Just got a usb oscope. Want to test a fanuc i64 inc encoder. Does anyone know this procedure?
    Thanks
    Steve austin
  4. You could use a dividing head on a mini mill if...

    You could use a dividing head on a mini mill if you find the correct cutters.
  5. I have a Fanuc Alpha servo machine which was...

    I have a Fanuc Alpha servo machine which was prewired for a 4th. I ordered the same Alpha motor/drive that would have come with the machine. I got the part numbers from the parts book. This has an...
  6. Hi VanC. I do have shields and the power cable...

    Hi VanC. I do have shields and the power cable appears to be correct. Can you think of anything else that would cause the motor to run sporadically with no alarm but the position error. That error...
  7. fanuc omd 4th axis randomly won't move 414 alarm excess error

    I have a Fanuc 0md Yang mill. And I found a Tsudakoma 4th from HGR minus a motor and internal wires. So I pieced together everything and got it running however after installing the motor cover it...
  8. You can gat mastercam with a machine sim that is...

    You can gat mastercam with a machine sim that is hooked up to a post. Still not Goode sim but 99 % there
  9. Replies
    18
    Views
    2,908

    You did a great job. I bought a Tsudakoma 4th...

    You did a great job. I bought a Tsudakoma 4th off HGR for 50$ but it had no motor, no gear as you have pictured and was disassembled in a box. Got it working not long ago. It was a job. My...
  10. We see the same thing with small radius tip...

    We see the same thing with small radius tip pencil cutters. I always attributed that to smaller tools cut with less pressure so there is no push off. Our situation is with 5 axis trunnions so flex...
  11. Replies
    511
    Views
    43,332

    Well I will still buy from Maritool. This title...

    Well I will still buy from Maritool. This title needs to change. In America you are innocent until proven and I think that American ideal should apply to business as well.
  12. Replies
    511
    Views
    43,332

    There is more difference than the length in the 2...

    There is more difference than the length in the 2 studs I pictured. Look at the Dia. Look at the nice Rad on the short fat stud.
  13. Replies
    511
    Views
    43,332

    The studs on our Okuma cat40's are short and fat....

    The studs on our Okuma cat40's are short and fat. I like them. Unlike the studs on my Yang cat40 in my garage which is long and thin. The Haas cat40's at work are same as mine. I have often...
  14. Replies
    12
    Views
    853

    That is it. Did you work hear?

    That is it. Did you work hear?
  15. Replies
    12
    Views
    853

    I just found I need a K word which is the lead in...

    I just found I need a K word which is the lead in in. or mm. Is that correct?
  16. Replies
    12
    Views
    853

    thread mill code on Acramatic A950

    Any one ever program a thread mill or helix in incremental with wear comp on a Acramatic A950 Cinci. This is for a 3 spindle gantry.
    Is code different than Fanuc? For wear comp you only need...
  17. I is HSM for roughing. Does it have a setting for...

    I is HSM for roughing. Does it have a setting for finish passes? I have feel like a spend more time finishing parts than I should.
  18. how do you calculate finish passes with endmills?

    how do you calculate finish passes with endmills? Of coarse different for different materials. Do you use standard ipt and calculate for radial chip thinning? I feel like I could increase feed of...
  19. If you have a tool probe measure diameter just...

    If you have a tool probe measure diameter just like any end mill
  20. deep pockets 7050 aluminum thin walls pushing out with finishing

    I am programming a aerospace part in aluminum 7050. Okuma mu6300. Part is held in dovetail and is tabbed to finish. This pocket is 2. x 6. x 2.0 deep. One wall is .06 thick and is pushing out when...
  21. Replies
    14
    Views
    2,013

    just google search "cnc"+"zone". Sheesh:dopeslap:

    just google search "cnc"+"zone". Sheesh:dopeslap:
  22. Replies
    7
    Views
    1,658

    Genius VanC. We use a big .122" x 6.3" disk mill...

    Genius VanC. We use a big .122" x 6.3" disk mill and always get vibs on the second side of the cut. Gonna try that next week!

    Another thing to improve rigidity when using tooling tabs is to use...
  23. I think the tolerance could be set too tight. ...

    I think the tolerance could be set too tight. One machine has the supernurbs option and the others have hicutpro. One machine is a mu6300 ac trunnion. 3 are mu4000 bc trunnions. The other 2 are...
  24. okuma hem/hsm not keeping up with called feed

    I program for six different Okuma mills with osp200 and osp300 controls. When running high efficient milling paths the machines cannot keep up with a constant say 100 ipm feed. It will achieve those...
  25. Replies
    8
    Views
    1,217

    I would use a collet and fiddle with it until I...

    I would use a collet and fiddle with it until I got it square with the axis
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4