Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: chippinchunks

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. That's another reasonable option. I might need to...

    That's another reasonable option. I might need to do what you mentioned earlier and fill the oil hole on the apron feed selector with JB then relocate the hole. After drilling I don't think the...
  2. Thanks for all the replies everyone. I'll clean...

    Thanks for all the replies everyone. I'll clean it up and use as is. 4GSR the 2 in the picture are for the apron feed selector and toggle cam feed clutch. I thought about adding Gits oilers but with...
  3. Structural integrity of SB13 apron after oil hole hack job

    HI everyone. This is the apron on my sb13. The previous owner drilled oil holes all over this apron. The 2 that I am most concerned with are shown in the pictures. The apron is cast iron and my...
  4. Awesome! Thank you Martin

    Awesome! Thank you

    Martin
  5. Questions about a 13" Southbend lathe with large spindle hole

    HI all.I recently purchased a 13" Southbend lathe Ser# 3433TKL10. I had a few questions. I've searched the Web looking for answers but I haven't been able to get any where. According to the Southbend...
  6. Replies
    10
    Views
    1,205

    Here's a Leblond search tip. When browsing online...

    Here's a Leblond search tip. When browsing online classifieds for Leblond Lathes. Type Lablonde Lablond Leblonde Le blond Loblond Lublond etc etc etc. About 6 months ago I found a face plate from a...
  7. I tend to side more with #1. In my opinion you...

    I tend to side more with #1. In my opinion you can never have enough. If i come across ads for used or new tooling that is reasonably priced I'll buy it up & pick out what I can use. Sometimes...
  8. Hendey 16x6 Lathe on Inland Empire Craigslist

    Spoke with owner. Looks to be in decent shape. No motor or motor pulley. No steady or follower rest. Says he might have a chuck for it. $600 asking price is somewhat negotiable. Located a few miles...
  9. ...& personal accountability. For $200 it...

    ...& personal accountability.

    For $200 it wouldn't last more than a couple hours if it was posted here.... cause I'd buy it. GL hope it finds a good home!

    Martin
  10. You have a good eye. The through hole on this old...

    You have a good eye. The through hole on this old 4 jaw measures 2" I guess it won't work. I did mark a line across the chuck & backplate before taking it apart. I was reading what you said making a...
  11. Replies
    1
    Views
    516

    Hi. I don't know the answer to all of your...

    Hi. I don't know the answer to all of your questions especially about the history of the company & such. I acquired a Barnes 13 lathe a few years ago & I too was missing quite a few of the change...
  12. When I bought the lathe an 8" 4 jaw was included...

    When I bought the lathe an 8" 4 jaw was included with the purchase.I assumed that it was a 4 jaw chuck for this lathe but after getting it home & checking threads I discovered that it wasn't. it's an...
  13. Will do! Im going to buy a few of those blanks....

    Will do! Im going to buy a few of those blanks. Thanks for the tips! The re-assembly process has already started i can't wait to start making some chips. Ill post some pics when I get her back...
  14. Awesome! Thank you Martin

    Awesome! Thank you

    Martin
  15. Thanks for the info Ramsay! Spindle nose...

    Thanks for the info Ramsay!



    Spindle nose is 1.375" long. Thickness of plate measured through the hub is 1.675".

    Martin
  16. After I get it back together that will probably...

    After I get it back together that will probably be one of my 1st projects with the lathe... making a 2nd backplate for my 4 jaw. I'm sure I'll have lots of questions as I've never attempted this...
  17. Thank you Joe. That means a lot. Well,...

    Thank you Joe. That means a lot. Well, perseverance finally paid off! I upgraded the clamping bar for a 3rd time, this time i used a 1x1x48 solid bar. Also beefed up the beater bar across the face of...
  18. After grinding excess material away from the...

    After grinding excess material away from the rectangular hole on the face of the backplate I determined that it wasn't a set screw. There was definitely a dimple from a drill mark in there but no...
  19. Tomorrow when metal mart is open Im going to...

    Tomorrow when metal mart is open Im going to upgrade 1.25" square tubes with solid bar. The tubing is starting to give now. Here's some proof that the clamp is holding up as stated. Tubing is .090...
  20. Joe was right. No screw I grinded away material...

    Joe was right. No screw I grinded away material from around the hole on the face & it's the same material. Paolo mentioned a boss or something possibly when the plate was manufactured. It's possible...
  21. Good advice. At this point I'm already this far...

    Good advice. At this point I'm already this far into it with the spindle holding tool I'll keep trying. I have a copy of the the original purchase record that leblond was kind enough to send me. The...
  22. I suppose this might be a topic for another...

    I suppose this might be a topic for another thread but this is probably going to be the easiest option at this point. My concern would be drilling & tapping the mounting holes for the chucks through...
  23. I think it might be keyed. There was dimple on...

    I think it might be keyed. There was dimple on the outer rim of the backing plate where the previous owner had attempted to use a drift to tap off the back plate at some point. The metal had really...
  24. Will do! I'll try heating backplate/cooling...

    Will do! I'll try heating backplate/cooling spindle then vice-versa.

    Thank you!
    Martin
  25. Spent most of the day beefing up the clamping...

    Spent most of the day beefing up the clamping bar. Added .25" steel plate to both sides of the bar & turned down some steel pipe to use as spacers inside the square tube. I also ditched the shim...
Results 1 to 25 of 48
Page 1 of 2 1 2