Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: iwananew10K

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    31
    Views
    1,114

    if you already used primer dont thin the...

    if you already used primer dont thin the paint...the point of thinning first coat is for it to flow into small pores and such to get a "grip" on the surface...and if you thin the paint now the extra...
  2. Replies
    31
    Views
    1,114

    its been years since i used Benjamin Moore...

    its been years since i used Benjamin Moore products....its was good stuff when i did.
    i have very recently used Sherwin Williams All Surface enamel (oil base)
    and got fantastic results....flowed...
  3. Replies
    10
    Views
    535

    hardware store...nipples,elbows and such.

    hardware store...nipples,elbows and such.
  4. Replies
    10
    Views
    535

    plumb them to the outside?

    plumb them to the outside?
  5. Thread: Red Lead

    by iwananew10K
    Replies
    9
    Views
    817

    spotting....like dykem....makes an excellent...

    spotting....like dykem....makes an excellent contrast...a bit toxic if care isnt taken.
  6. google is your friend...sometimes...plenty of...

    google is your friend...sometimes...plenty of hits.

    Pacific Marine Review - Google Books
  7. Replies
    18
    Views
    698

    http://vintagemachinery.org/pubs/1617/17785.pdf

    http://vintagemachinery.org/pubs/1617/17785.pdf
  8. Replies
    12
    Views
    687

    lots of detailed pics will be the most help....

    lots of detailed pics will be the most help.
    even of the area where you dont see a number.
    lots of good pics.
  9. Replies
    12
    Views
    687

    yep!!!! thanks for the correction!!! looked at...

    yep!!!! thanks for the correction!!! looked at the wrong column..good catch!

    as noted above...117C...still pg 4 of the documnent.
  10. Replies
    18
    Views
    698

    correct me if im wrong....but i think TA100 is...

    correct me if im wrong....but i think TA100 is just the generic designation that spans all size lathes?? a suffix letter designates the size?

    ex- TA100R= heavy 10 taper attachment
    ???
  11. Replies
    8
    Views
    516

    FWIW- IMO the "teeth" are a good...

    FWIW- IMO the "teeth" are a good thing....increases surface area to carry more oil..they dont gotts to be purty.:)
  12. Replies
    12
    Views
    687

    more pics will certainly help...particularly in...

    more pics will certainly help...particularly in the area kitno mentioned.
    which is a couple inches to the left of the numbers in your pic and in the space between the v and flat way...by where the 2...
  13. Replies
    12
    Views
    687

    you might think after all this time.... ...

    you might think after all this time....

    Herbert ND Lathe info required
  14. you obviously need a new lathe.:) ...

    you obviously need a new lathe.:)

    kidding...check all the parts for a burr,ding,embedded chip.
  15. Replies
    3
    Views
    368

    if you want to make it "clock" to the right...

    if you want to make it "clock" to the right position....its easy to figure how thick a shim you need....say its a 16tpi thread...1/16=.0625" so say you need a 1/2 turn to get where you want...
  16. you might find it difficult to get an 8 rib J...

    you might find it difficult to get an 8 rib J section motor pulley that small...a 6 will do fine....might even be best...IDK.:)
  17. if its listed anywhere it wont be an option for...

    if its listed anywhere it wont be an option for long.
  18. get it...you cant get hurt at 800

    get it...you cant get hurt at 800
  19. when you reply you will see a box at the top that...

    when you reply you will see a box at the top that looks like a tree in a picture frame...click that to link pics.

    i would go with at least a 6 rib...thats about 3/4" wide IIRC...i "think" the...
  20. theres really not much advantage to using a...

    theres really not much advantage to using a grooved spindle pulley....plus its a PITA and requires some modification of your orginal part....you may want to get the original set up working again...
  21. for the record....your spindle pulley does not...

    for the record....your spindle pulley does not need to be grooved for the belt.

    and if you want to work the maths...its not the diameter...its the circumference you need to figure...as if it were...
  22. just in case.... poly v = *serpentine...

    just in case....
    poly v = *serpentine belt*....so yes, flat belt.:)

    im in total agreement on the smaller size motor pulley....keep in mind at 90hz your 1140rpm motor effectively becomes a 1725ish...
  23. pics of what you have now of the drive parts will...

    pics of what you have now of the drive parts will help.
    someone might have what youre missing.
  24. Replies
    9
    Views
    518

    first pattern underdrive workshop 9" model C ...

    first pattern underdrive workshop 9" model C

    pg 11 of this document, courtesy of Steve Wells-

    http://www.wswells.com/data/catalog/1939_Catalogue_No.50/1939_Catalogue_No.50.pdf
  25. Replies
    9
    Views
    848

    yes,to above. BUT runnung that lathe without...

    yes,to above.

    BUT runnung that lathe without oil cups or at least a plug in the hole is a recipe for disaster....one little piece of debris falls in that hole and siezes the spindle at...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4