Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: FrankieB

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    870

    Dirt between the part and jaws or dirt between...

    Dirt between the part and jaws or dirt between the jaws and chuck. A thou taper isn’t anything i would worry about. Just program it out.
  2. Replies
    10
    Views
    867

    And turning off the parameter lock.

    And turning off the parameter lock.
  3. Od figure 8 oil groove: sl30 with live tooling

    UPDATE: i got it figured out,all i can say is watch the decimal points on the degrees.






    T1111 m31
    M133 p500
    G19 m08
  4. Replies
    10
    Views
    867

    no i am not in debug mode. Yes you need to change...

    no i am not in debug mode. Yes you need to change a parameter to keep the spindle from turning during the drilling and tapping cycle, since it is not an exclusive live tool cycle.
  5. Replies
    10
    Views
    867

    I canít use a g83. To use it off center i have to...

    I canít use a g83. To use it off center i have to change a parameter that is locked.
  6. Replies
    10
    Views
    867

    sorry it is a 2004 haas sl30

    sorry it is a 2004 haas sl30
  7. Replies
    10
    Views
    867

    Peck drilling on face with live tooling

    Any suggestions on peck drilling on the face of the part with live tooling. I canít use a g83 because when i try to change the parameter ( no spin can) it says the function is locked. These holes are...
  8. Replies
    7
    Views
    901

    I will have to look on the diameter setting, not...

    I will have to look on the diameter setting, not sure if i can use a g93 or not. This is an older machine.
  9. Replies
    7
    Views
    901

    Sorry it has taken so long to get back to this. ...

    Sorry it has taken so long to get back to this.

    The way i take it is, if i put a feed rate in there with a start and end point in degrees, then the feed and the speed of the c drive will jive?
  10. Replies
    7
    Views
    901

    I may be over thinking this. I keep thinking the...

    I may be over thinking this. I keep thinking the feed rate needs to be calculated like a threading or tapping cycle.
  11. Replies
    7
    Views
    901

    sl30 lathe oil grove

    hello all, i am trying to figure out the math needed to get a feed rate for this oil groove. I will being using radial live tooling with an endmill. What i have come up with so far is...
  12. Replies
    6
    Views
    1,062

    That was my conclusion also. I was hoping...

    That was my conclusion also. I was hoping someone had figured out a work around to do it.

    Thanks for the reply.
  13. Replies
    6
    Views
    1,062

    I donít have enough holders and the one i do have...

    I donít have enough holders and the one i do have i want to use a boring bar in.
  14. Replies
    6
    Views
    1,062

    Sl30 using tailstock to drill?

    Is there anyway to use the tailstock to drill with a sl30 lathe? Anyway to slow the feed rate of the tailstock?
    Thank you
    Frankie
  15. Replies
    2
    Views
    608

    Thank you Frankie

    Thank you
    Frankie
  16. Replies
    2
    Views
    608

    Sl 30 chuck setting

    On a haas sl30 lathe, is there a setting that needs to be changed to id grip?

    Thank you
    Frankie
  17. No i donít have a y axis.

    No i donít have a y axis.
  18. Replies
    1
    Views
    736

    Haas servo 300 bar feeder question

    I want to use the bar feeder as a part stop. The manual has a program example to do this.
    G105 Q7 (LOAD PUSH ROD)
    G160 (ALLOW THE USE OF THE V AXIS)
    G00 V-20.0 (POSITION THE PUSH ROD)
    M00 (LOAD...
  19. Haas sl30:radial live tooling with a c axis

    I am trying to mill two flates with a radial live tool and the c-axis. I will be using the tail stock on this part so i will not have the clearance to use axial live tooling. I am wanting to do this...
  20. Replies
    1
    Views
    610

    VZSHZ= on a haas lathe?

    Any one know if you can do a zero shift on a haas lathe like you can on an okuma?
    Thank you
  21. Replies
    2
    Views
    725

    Thank you for the input.

    Thank you for the input.
  22. Replies
    2
    Views
    725

    Haas SL30:noob to live tooling

    Part Dim: 2 inch diameter with a face slot .200 deep across the full face. The machine has axial live tools with c-axis, no y axis.

    Hello All, Can someone give me and example of a g code program...
  23. Replies
    0
    Views
    322

    Haas SL30:noob to live tooling

    Part Dim: 2 inch diameter with a face slot .200 deep across the full face. The machine has axial live tools with c-axis, no y axis.

    Hello All, Can someone give me and example of a g code program...
Results 1 to 23 of 23