Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: agieman

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. where is the water coming out of the filters....

    where is the water coming out of the filters. they work from inside out and from bottom to top. as they clog the water level on the side of the filter rises. The pressure usually stays low till the...
  2. Replies
    2
    Views
    209

    A and B are on/off times as I recall. do you have...

    A and B are on/off times as I recall. do you have a manual? shoot me your email.
  3. Replies
    6
    Views
    586

    What machine? part material? part thickness?...

    What machine? part material? part thickness? wire? how much error? number of passes?
  4. Replies
    4
    Views
    623

    he is duplicating the function. does he have the...

    he is duplicating the function. does he have the X value to be entered at 0.0000. if so, then the center of the wire will be zeroed on the edge of the part and it will automatically comp for the...
  5. Replies
    2
    Views
    268

    hi, send me your pics or call me

    hi, send me your pics or call me
  6. Replies
    6
    Views
    1,030

    did you find anything out about the titan...

    did you find anything out about the titan machines?
  7. Replies
    11
    Views
    969

    the 510 generator does need periodic tune ups....

    the 510 generator does need periodic tune ups. How are your cables inspect them and make sure the terminations are good.
  8. Replies
    6
    Views
    1,030

    does your sodick use G92 to set reference at the...

    does your sodick use G92 to set reference at the start of every shape in your program? if so, Drill 20 will use it to create drill points so you only need one program for both wire and drill.
  9. Replies
    6
    Views
    1,030

    Drill 20 is a nice machine. do you have wire EDM?...

    Drill 20 is a nice machine. do you have wire EDM? if so, what make model? how small of a hole do you need to go down to?
  10. Replies
    3
    Views
    445

    if it act up using normal tank fill button use...

    if it act up using normal tank fill button use m34 in MDI line.
  11. Replies
    4
    Views
    839

    just my 2 cents. charmilles machines have...

    just my 2 cents. charmilles machines have collision protection. this can be a life saver for newbies! Also,they do not charge for phone support. if machine is still supported all calls are free. im...
  12. Replies
    17
    Views
    1,765

    i would keep the filter in if it generates an...

    i would keep the filter in if it generates an error msg open the opposite door and find the "spaceship" sensor at knee high height. jumper 2 wires together. your mode 6 problem is likely reference...
  13. Replies
    15
    Views
    1,481

    coolest i ever saw was about a 3in tall .5 in...

    coolest i ever saw was about a 3in tall .5 in "tornado" growing out of a cavity. pre cell phone day or y'all would see a picture!
  14. Replies
    15
    Views
    1,481

    you wont find much because "uncontrolled arcing...

    you wont find much because "uncontrolled arcing damage" leads to wire breakage and stops the process. It will create a line in your piece most likely and hardly a good representation of arcing...
  15. Replies
    17
    Views
    1,765

    Hi Clayton, glad to hear it! on the back bottom...

    Hi Clayton, glad to hear it! on the back bottom ground cable there was a small reference line included. did you replicate it?
  16. Replies
    17
    Views
    1,765

    Clayton what settings are you using they should...

    Clayton what settings are you using they should be
    EROS T M=5 t=5 I=13 pr=10 p=13-20 Td=25 HC=6
    EROS S cw=2 fw=17 Aw=120 B=1 K=10 Q=4 Str=2 Qo gage =5 bar. this is for CCA wire but brass will...
  17. Replies
    17
    Views
    1,765

    Hi Clayton, you are barking up the wrong tree on...

    Hi Clayton, you are barking up the wrong tree on that one. that is to retract wire after a break. Here's what to do
    thread the wire. with handbox on run the wire grab the black wheel and try and...
  18. Replies
    17
    Views
    1,765

    find Fm and UFS lines in schematics there is a...

    find Fm and UFS lines in schematics there is a wid board on back of machine that all spark cables come into. - is to the carbides + to the table
  19. Replies
    17
    Views
    1,765

    Hi Clayton, it is necessary to disconnect the the...

    Hi Clayton, it is necessary to disconnect the the long lengths of spark cable and main unit of generator in the SF (fine finishing) mode. there is a portion of the generator mounted in the machine...
  20. Replies
    17
    Views
    1,765

    Hi Clayton, your reference lines or fine module...

    Hi Clayton, your reference lines or fine module lines are open. do you have prints? check the gap boxes on the end of the upper and lower arms.There are 2 air lines to each box they should change...
  21. Thread: Agie 100 parts

    by agieman
    Replies
    12
    Views
    2,187

    THAT IS NOT AN AC100! that is a DEM315/2

    THAT IS NOT AN AC100! that is a DEM315/2
  22. Thread: Agie 100 parts

    by agieman
    Replies
    12
    Views
    2,187

    Andy you need to home the z axis then home u-v...

    Andy you need to home the z axis then home u-v axes. then z will go down.
  23. Replies
    15
    Views
    3,987

    hi Kevin the classic was made in Losone just like...

    hi Kevin the classic was made in Losone just like the challenge AND the machine tool is basically the same.
  24. Replies
    1
    Views
    520

    going from memory here but 140 is start in short...

    going from memory here but 140 is start in short ckt. i believe. check if there is continuity between wire and table. there should not be.
  25. Replies
    7
    Views
    842

    well you may be able to get training from GF for...

    well you may be able to get training from GF for that machine. if not you have us!
Results 1 to 25 of 279
Page 1 of 12 1 2 3 4