Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cal Haines

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Make sure that you verify that the MG is turning...

    Make sure that you verify that the MG is turning the correct direction when you first fire it up.

    Cal
  2. Replies
    4
    Views
    295

    The A-B resistor pair connect to the shunt coil...

    The A-B resistor pair connect to the shunt coil of the FA (Field Acceleration) relay. The FA relay also has a series coil, which is connected in series with the spindle motor's armature. The relay...
  3. Replies
    4
    Views
    295

    That problem is related to the AP (anti-plugging)...

    That problem is related to the AP (anti-plugging) relay. I explain what's going on it this post:
    MG 10EE troubles

    This has nothing to do with the two 1600 Ohm resistors, the A-B resistor pair....
  4. My conversion checklist walks you through this....

    My conversion checklist walks you through this. (I was missing a photo, but it's back now.) You need to check the overload heaters as well as the coil voltage; don't assume that because one is...
  5. The first photo shows the DC exciter...

    The first photo shows the DC exciter (belt-driven, on the top) and the DC generator (on the bottom). The second photo is not the generator, it's the DC spindle drive motor. The back of the DC control...
  6. Replies
    14
    Views
    1,400

    Newer square-dials with only one oil sight glass...

    Newer square-dials with only one oil sight glass take just DTE Light in the center reservoir, with services the spindle bearings as well.

    Cal
  7. Replies
    37
    Views
    1,850

    1) The five metering units on the apron manifold...

    1) The five metering units on the apron manifold go to: left and right side of cross slide, rear flat way, front V way and thread dial. If you remove the thread dial you'll see a hole at about 10...
  8. Replies
    102
    Views
    6,320

    You're talking about the 1962 Modular drive...

    You're talking about the 1962 Modular drive machine that you were looking at at the beginning of this thread, correct?

    DualValve may be thinking in terms of motor/generator machines, which are...
  9. The clamp that normally holds the draw bar...

    The clamp that normally holds the draw bar stationary when the taper attachment is not is use is shown in the top/rear of this photo:

    274696

    Here's what the "bridge" and clamp screw look like:...
  10. Hi Nick, Can you post photos of the back end...

    Hi Nick,

    Can you post photos of the back end of your cross-slide, so I can see what you've got left. I need to see what draw bar you have and how the cross-feed nut is attached.

    Cal
  11. Replies
    13
    Views
    1,160

    I'm pretty sure that's a serial number. At least...

    I'm pretty sure that's a serial number. At least on 10EEs, Monarch stamped the serial number of the machine on the backs of chucks and the bottoms of rests.

    Cal
  12. Replies
    14
    Views
    1,400

    DTE 24 hydraulic oil IS NOT the correct oil for...

    DTE 24 hydraulic oil IS NOT the correct oil for your headstock! You want DTE Light. Hydraulic oils are engineered for very different applications. We've had this discussion over and over. The only...
  13. It's hard to tell much from photos or a video....

    It's hard to tell much from photos or a video. Two tests will tell you a lot about the condition of the ways:

    Check the clearance between the tailstock flat way and the saddle using a feeler...
  14. I sent you an e-mail. Cal

    I sent you an e-mail.

    Cal
  15. Your lathe is "round-dial" 10EE and is equipped...

    Your lathe is "round-dial" 10EE and is equipped with the "electric leadscrew reverse" (ELSR) option. ELSR is really a misnomer: all the mechanism does is stop the spindle motor when the saddle bumps...
  16. Thanks Bill. The Hammond 195M20 is pretty...

    Thanks Bill.

    The Hammond 195M20 is pretty pricey, $329 from Newark: https://www.newark.com/hammond/195m20/dc-reactor-choke-20mh-20a-15/dp/52F9510

    The 10mH version, 195J20, is $169 but Newark...
  17. If you have specs for a choke for a large frame...

    If you have specs for a choke for a large frame Reliance 3HP motor, please post.

    Cal
  18. What's serial number and build date of the...

    What's serial number and build date of the machine? What type of drive did it originally have? It's hard to read the data plate, it doesn't look like that for motor/generator (MG) drive machines. In...
  19. Replies
    39
    Views
    2,301

    The 3kVA boost transformer is an Acme...

    The 3kVA boost transformer is an Acme T-2-53013-S. Its two 240V primary windings are in parallel and the two 120V secondary windings are also in parallel. I think that makes the no-load boost voltage...
  20. Replies
    39
    Views
    2,301

    GES DGSC-M 10EE Fincor Drive schematics

    Here are the three Fincor drive diagrams that are of the most interest:
    271600





    271604
  21. Thread: Mike C.

    by Cal Haines
    Replies
    10
    Views
    1,638

    He also said that he appreciated the fact that...

    He also said that he appreciated the fact that people here were concerned about him and indicated that he was going to try to get back on soon.

    Cal
  22. Replies
    39
    Views
    2,301

    I'm busy for the next several days. I'll try to...

    I'm busy for the next several days. I'll try to fix/post the wiring diagrams early next week.

    Cal
  23. Replies
    342
    Views
    44,856

    That line is the overflow for the center...

    That line is the overflow for the center reservoir. You're looking at the fitting that threads into a tapped hole in the left/back corner of the headstock. If you take the top cover off and look in...
  24. The guy with the DC panel parts is still around....

    The guy with the DC panel parts is still around. He's going to see what he has left. At one point he had two sets of 598 forward/reverse contactors and three field acceleration (FA) relays.

    Cal
  25. Replies
    39
    Views
    2,301

    Greg, Are you, by chance, using an iPhone to take...

    Greg, Are you, by chance, using an iPhone to take your photos?

    Cal
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4