Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: labeeman

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Yep if it ain't broke don't fix it.

    Yep if it ain't broke don't fix it.
  2. A sheared taper pin on the lead screw.

    A sheared taper pin on the lead screw.
  3. Replies
    7
    Views
    550

    I do not know but I have a square dial machine...

    I do not know but I have a square dial machine with a round dial saddle and apron.
  4. Replies
    8
    Views
    611

    That will work unless USPS runs over it with a...

    That will work unless USPS runs over it with a vehicle which I have had done several times.
  5. Replies
    94
    Views
    4,771

    How you get them to move is beyond me.LOL

    How you get them to move is beyond me.LOL
  6. Replies
    7
    Views
    649

    Monofilament fishing line should work instead of...

    Monofilament fishing line should work instead of wire.
  7. Here are the part #'s for the bottom pulleys. ...

    Here are the part #'s for the bottom pulleys.

    275654
  8. Top pulley is 5.75" bottom is 6.5"

    Top pulley is 5.75" bottom is 6.5"
  9. Replies
    26
    Views
    1,718

    Unplug your old one and check for continuity you...

    Unplug your old one and check for continuity you have a 90% chance it is good. It is the white ceramic square thing mounted on a little board that plugs in.
  10. Replies
    26
    Views
    1,718

    I am guessing here but that small board on the...

    I am guessing here but that small board on the top left looks like the field control card and that card is Cheap on ebay the lower board is your Main control for the armature. If you can disconnect...
  11. Replies
    26
    Views
    1,718

    Your links do not work.:(

    Your links do not work.:(
  12. Looks Good On the field check. Next check the...

    Looks Good On the field check. Next check the amps on the motor how much it is drawing when not cutting.
  13. Yep you can check it there.

    Yep you can check it there.
  14. Replies
    26
    Views
    1,718

    Middle picture DC drive controller has some...

    Middle picture DC drive controller has some shorted SCR's and will need to be replaced If not the whole DC drive controller.
  15. [QUOTE=Mac007;3470060]In the pecker head of the...

    In the pecker head of the motor there should be wires labeled F1 F2
  16. [QUOTE=Mac007;3469897]What is your field voltage?...

    What is your field voltage? If not up to 120VDC you have a problem with that circuit and the first thing you do is change the tube which you have done but if your 120VDC is not right that circuit is...
  17. See above your post

    See above your post
  18. Check your field voltage it should be full...

    Check your field voltage it should be full voltage at the lower rpm's and that relay should not be kicking in. That relay should only kick in when the motor draws a high current on the armature to...
  19. Replies
    37
    Views
    2,201

    I am guessing but what you have is a (works in a...

    I am guessing but what you have is a (works in a drawer) not an easy machine to trouble shoot due to all the other tubes which are not easy to sub due to not being readily available.
  20. Replies
    37
    Views
    2,201

    If this is a tube machine you do not need 3 phase...

    If this is a tube machine you do not need 3 phase power just 220VAC
  21. If there is no taper attachment that bolt is not...

    If there is no taper attachment that bolt is not there but if there is a taper attachment there is a shoe that would be running around loose if the bolt is missing.
  22. That bolt is used to lock the cross slide down...

    That bolt is used to lock the cross slide down when using the taper attachment.
  23. Replies
    14
    Views
    1,625

    That will not happen as the old oil has turned to...

    That will not happen as the old oil has turned to varnish.
  24. Replies
    102
    Views
    6,986

    A 10EE modular only requires single phase so a...

    A 10EE modular only requires single phase so a single phase transformer is all that is required.
  25. Replies
    6
    Views
    678

    The measurement from the split line to the...

    The measurement from the split line to the contact on the base has more use.
Results 1 to 25 of 402
Page 1 of 17 1 2 3 4