Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ToolCat

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,516

    Yes, it does. Three AAs. ...

    Yes, it does. Three AAs.
    http://airgraver.com/shaper/20180711_183224.jpg
  2. Replies
    5
    Views
    1,516

    Brother batteries

    This is from the brother wedm manual. It sounds risky. I would rather change the batteries while the machine is running.
    http://airgraver.com/shaper/20180708_161837.jpg
  3. Got it working. Thank you. It was power...

    Got it working. Thank you. It was power fluctuation related. It is on a rotary phase converter and one leg is higher than the other two. I swapped two of the leads and the motor ran without the...
  4. Brother HS3100 shutting down when water pump is turned on

    Any ideas what would cause the machine to shut right off when I turn the water on? The pump starts to spin for a fraction of a second but then the whole machine powers off. t powers right back...
  5. Replies
    2
    Views
    1,228

    Ok,thanks.

    Ok,thanks.
  6. Replies
    2
    Views
    1,228

    What is this plug on a Makino RMC 55

    Anyone know, what is the blue plug on the right for?
    This is on a Makino RMC 55.

    http://engravingschool.com/forum-pics/20160917_091000.jpg
  7. Replies
    13
    Views
    2,145

    Touch probe to a Makino rcm55 - fanuc 0M

    Trying to add a touch probe to a Makino rcm55 - fanuc 0M.
    From what I read it can be done at pin 49 on the M18 connector. I have located M18, and it has a cable connected to it. I am trying to...
  8. Here are further descriptions found in the...

    Here are further descriptions found in the parameters manual:
    http://airgraver.com/shaper/g83%20small-diameter%20peck%20drilling%20cycle%20parameters.gif
  9. In this controller all of the parameters it...

    In this controller all of the parameters it refers to that I posted from the manual above are set to zero. I just now changed parameter #304 to 230, and then went to MDI and entered M230. No...
  10. G83 "small-diameter peck drilling cycle", Fanuc OM

    Has anyone used what the OM manual calls "small diameter peck drilling cycle"? There is a normal G83 mode, but I see in the manual there is another mode that can detect overload torque of a small...
  11. Replies
    3
    Views
    1,753

    Harig air-flo endmill fixture manual

    Hi, Last night I was hunting the web for a Harig air-flo endmill fixture manual. No luck, except for the sites with the dang popups/spams that want you to first sign up to download. I knew I had...
  12. Replies
    1
    Views
    2,754

    Figured out the problem. Operator error. Tool 3...

    Figured out the problem. Operator error. Tool 3 (a groove tool) offset number was set at 6.
  13. Replies
    1
    Views
    2,754

    Tool Data Set "guide on/off" - Okuma lb15

    Okuma lb15 OSP5000L-G
    Can anyone help with why the graphic display of the cutter on the "tool data set" offset page isn't displaying the selected one?
    I've selected a boring bar for tool#6, but...
  14. Replies
    3
    Views
    2,859

    I am interested. I tried to pm but your box is...

    I am interested. I tried to pm but your box is full. Great--yes, please email pics. The email that is in my account will work for the pics. Did you find a better jack to replace them with?

    I...
  15. Replies
    3
    Views
    2,859

    11,000 lbs pallet jack

    I am in the market for a 10,000lbs pallet jack. I believe Liftrite use to make one, but on their site 8,000 is the highest now. Lift-Rite: Heavy Duty Trucks

    Google searching I see...
  16. Replies
    19
    Views
    6,327

    I was using this assembly to help level the...

    I was using this assembly to help level the machine. The column/knee Z surfaces weren't worn that bad compared to how bad the y and x were. I locked the column/knee and then checked with the...
  17. Replies
    19
    Views
    6,327

    Kevin, I was only into the knee of the Cincinnati...

    Kevin, I was only into the knee of the Cincinnati and made a coupler for a part that by the look of it someone else did another time. By comparison it is like a tank compared to the k&T.

    Thanks...
  18. Replies
    19
    Views
    6,327

    Thanks everyone. Kevin, yes, crazy inside...

    Thanks everyone. Kevin, yes, crazy inside there. lol! Did you see in the pics the front end was apart twice? When it was apart the first time I blew mineral spirits through the port that the...
  19. Replies
    19
    Views
    6,327

    K&T 2H Restoring Project

    Hi, Finally finished a K&T 2H restoring project that was started last Fall. I took pics along the way and uploaded them to a page. There are 230 photos. K&T 2H Photos Link..click here. The page...
  20. Replies
    31
    Views
    16,036

    The drive is back in and working! I had decided...

    The drive is back in and working! I had decided at the last minute to ship the entire drive to www.cnc-electronics.com I shipped it to them in Virgina by FedEx 2 day. They received it Friday at...
  21. Replies
    31
    Views
    16,036

    As you suggested I began comparing readings from...

    As you suggested I began comparing readings from the seven circuits but not including the two with the components that I removed. There are inconsistencies in the readings. I just finished...
  22. Replies
    31
    Views
    16,036

    You're right Pipes. I found two burned out...

    You're right Pipes. I found two burned out diodes. I have pulled them already. Here is a photo of a good one still in place. Can beg your help again to identify so I can order them too? With...
  23. Replies
    31
    Views
    16,036

    Thanks again Pipes! Here is a link to that...

    Thanks again Pipes! Here is a link to that earlier photo of the board but at a higher resolution.
    I circled in red where the two small transistors are at as well as where the missing larger one...
  24. Replies
    31
    Views
    16,036

    Thanks Pipes. I ordered one of those overnight...

    Thanks Pipes. I ordered one of those overnight and it was delivered today. I was about to replace it and then I noticed two more small transistors that have blown. This is near the missing larger...
  25. Replies
    31
    Views
    16,036

    That is good news Pipes! I'll find and solder in...

    That is good news Pipes! I'll find and solder in the missing transistor. The other three near are: ET391 FUJI. I'll search for the same. The transistor module looks like it will be an easy...
Results 1 to 25 of 181
Page 1 of 8 1 2 3 4