Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: friesen

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. What year machine? Are you using dwo? Somewhere...

    What year machine? Are you using dwo? Somewhere the y and z has to get set for your setup this to work correctly.
  2. I'd spend a bit of time trying to understand if...

    I'd spend a bit of time trying to understand if there is a root cause to the failure, whether mesrepaired drive, or failed motor, or bad resistor, maybe this repair guy would have some ideas.
  3. Edited my post,it got deleted. Subscribe to eBay...

    Edited my post,it got deleted. Subscribe to eBay Haas vector drive -repair if one comes up you'll have very little time to buy if it's a good deal.
  4. Replies
    28
    Views
    2,230

    Someone has posted a schematic on *zone for the...

    Someone has posted a schematic on *zone for the older 15/20 drives.
  5. Replies
    13
    Views
    1,438

    271889271890 I'm just trying to follow where...

    271889271890

    I'm just trying to follow where in the chain those voltages can matter, not doubting its possible.

    Basically the servo drives are non smart, all they do is take a signal from the...
  6. Replies
    2
    Views
    625

    Not sure exactly how the tm1 compares to a vf2,...

    Not sure exactly how the tm1 compares to a vf2, but have you checked to see if you can do one side at a time? That solves a number of issues you'll have if you take it clear off.
  7. Replies
    13
    Views
    1,438

    As to the voltage, why would that be? This is...

    As to the voltage, why would that be? This is the updated control, its not the 96 vintage.
  8. Replies
    13
    Views
    1,438

    Its not immediately obvious to me which thrust...

    Its not immediately obvious to me which thrust bearing, X or Y?
  9. Replies
    13
    Views
    1,438

    X vs Y cut finish

    Any ideas what to look at first for cut differences between the X and Y?

    The attached photos were spring passed at 9500RPM / 100IPM with a 1/2" HTC 3 flute carbide tool. The cut sounds exactly...
  10. Replies
    30
    Views
    1,794

    Does this machine have a probe?

    Does this machine have a probe?
  11. Replies
    30
    Views
    1,794

    Where do the wires from the CPU end at?

    Where do the wires from the CPU end at?
  12. Replies
    30
    Views
    1,794

    The power supplies are known for going bad. When...

    The power supplies are known for going bad. When they go bad there are any number of symptoms. If it was my machine I'd change it before working in anything else, or at least check the voltages...
  13. Replies
    30
    Views
    1,794

    The number one thing to try on older machines is...

    The number one thing to try on older machines is a new power supply.
  14. Replies
    17
    Views
    1,749

    I bought a walrus pump and added a washdown at...

    I bought a walrus pump and added a washdown at one point, but gave up on it as it used too much coolant, if anything plugged at all there would be a lake of coolant. The only way I could see this...
  15. Replies
    17
    Views
    1,749

    @aa9100d which washdown system did you buy?

    @aa9100d which washdown system did you buy?
  16. Replies
    3
    Views
    781

    Are you aware that unless the probe is exactly...

    Are you aware that unless the probe is exactly centered the it needs to be in the same orientation every time?(ie, not 180 degrees difference) Even if it is exact, I'd still suspect a slight...
  17. Replies
    8
    Views
    1,843

    No, it's more of a sqeal noise, double pitch on...

    No, it's more of a sqeal noise, double pitch on the way out.
  18. Replies
    8
    Views
    1,843

    I'm not sure, I think I did though. Everything...

    I'm not sure, I think I did though. Everything is and was well lubed. This noise doesn't seem to get worse with time, and so far there is no leak. This noise is somewhat worse in the lower ranges,...
  19. Replies
    8
    Views
    1,843

    There are counterbalances available. Counter...

    There are counterbalances available.

    Counter Balance Cylinder Only as Compared to Old Haas(R) PN# 93-1460 VFOE Thru VF2 | eBay

    COUNTERBALANCE TANK/CYLINDER KIT, 40 CU FT (VF-E-2) |...
  20. Replies
    8
    Views
    1,843

    Dredging this up, I'm still dealing with this. ...

    Dredging this up, I'm still dealing with this. I'm finding that the counterbalance is quite warm to the touch. Has anyone else seen this type of issue? Its annoying to hear the machine groaning...
  21. I had been using a full synthetic cimcool...

    I had been using a full synthetic cimcool 3100-vlz. Last time I tried to order they were about 3 weeks out and I couldn't find any anywhere. Plus I got tired of the whole distributor song and dance....
  22. I do with my 96 vf2, 20/15 vector drive. I do...

    I do with my 96 vf2, 20/15 vector drive. I do have Accel set to 150% or so, which you can't do on ngc I don't believe.
  23. Replies
    26
    Views
    4,065

    If it works, why not use it? If you must do...

    If it works, why not use it?

    If you must do linuxcnc, learn the control a bit, you may soon see why even a 93 control has some significant items that will be hard to replicate with linuxcnc. Like...
  24. Replies
    10
    Views
    1,342

    I don't have mine connected right now so it won't...

    I don't have mine connected right now so it won't let me scroll the options. I did find some params the HFO sent me though.266038
  25. Replies
    10
    Views
    1,342

    Isn't there a plain 210h in the setup? I recently...

    Isn't there a plain 210h in the setup? I recently added a hrt210h to Mill v17, haas really didn't have much info for me, basically told me to select it from the menu. It worked out of the box for me....
Results 1 to 25 of 261
Page 1 of 11 1 2 3 4