Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ray Behner

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    11
    Views
    604

    If that's the one that was in Elida, I was quoted...

    If that's the one that was in Elida, I was quoted several thousand for one Z power feed for a Toolmaster D1. There again, no rapids.
  2. Replies
    11
    Views
    604

    Just a suggestion, make adapter plates for the...

    Just a suggestion, make adapter plates for the drives and use power feeds like Servo and others. I've got them running one rotary table, cross slides on 2 lathes, big tailstock on Amer. lathe and...
  3. Replies
    29
    Views
    1,371

    Just noticed your's has a steering wheel and not...

    Just noticed your's has a steering wheel and not a tiller. Do you have a horn button on the fwd./rev/ throttle lever?
    If you step on the right pedal it should go faster. Like a passing gear. Have...
  4. Replies
    11
    Views
    750

    Yep, still there, just west of Sharon Center.

    Yep, still there, just west of Sharon Center.
  5. Replies
    29
    Views
    1,371

    PM sent........

    PM sent........
  6. Replies
    2
    Views
    481

    No, this was 11 days ago on Craig's list. They...

    No, this was 11 days ago on Craig's list. They must have sold and the listing taken down.
  7. Replies
    2
    Views
    481

    9" south bent change gears FS

    South Bend Lathe Parts - tools - by owner - sale
    I know nothing
  8. Replies
    11
    Views
    1,932

    YouTube...

    YouTube
  9. Replies
    4
    Views
    707

    Just my opinion but, we don't hear enough of...

    Just my opinion but, we don't hear enough of those stories. Thank you Rex TX
  10. Replies
    49
    Views
    3,095

    Here's an SPI 0 to 1" for $311 bucks.....without...

    Here's an SPI 0 to 1" for $311 bucks.....without anvils. The Shar's is only $78 bucs....with anvils. Oh and they're the same damn thing!! Made by the same Chinese company. SPI makes NOTHING! They are...
  11. Replies
    49
    Views
    3,095

    I have a 0 to 6" set from Shar's. They have never...

    I have a 0 to 6" set from Shar's. They have never let me down. Oh and a 6 to 7" Insize. If you buy used, make sure you get the complete anvil set and a standard. Most anvils cover a range of pitches....
  12. Replies
    3
    Views
    392

    Most generally it would be 1/8th inch pipe with a...

    Most generally it would be 1/8th inch pipe with a coupling and a zerk fitting.
  13. Just another idea to throw at you. Servo powered....

    Just another idea to throw at you. Servo powered.

    YouTube
  14. Replies
    17
    Views
    1,001

    Yep, here's the popcorn. YouTube...

    Yep, here's the popcorn.
    YouTube
  15. Replies
    17
    Views
    1,001

    I've gone that deep in 1045, but never 4140. I...

    I've gone that deep in 1045, but never 4140. I have a Sterling gun drill with spray mist. Hi pressure is better, but too pricey. You'll need a very slow feed rate. Like maybe .0008, or even less. RPM...
  16. Replies
    351
    Views
    88,555

    Wow! Solid billet 80/20.

    Wow! Solid billet 80/20.
  17. Bill, As far as I can see, that CS has a...

    Bill,

    As far as I can see, that CS has a dovetail. Here's my Sheldon with two tool posts. Sometimes I snug them up for a lot of cutting off or whatever, or slide it way to the back and out of the...
  18. Replies
    10
    Views
    933

    Mike, Those are hard jaws.

    Mike,
    Those are hard jaws.
  19. Replies
    2
    Views
    513

    I'll take them. PM sent

    I'll take them. PM sent
  20. Replies
    2
    Views
    472

    Lee's Machinery used to sell them,(I think). ...

    Lee's Machinery used to sell them,(I think). I've dealt with them in the past on my Chevalier mill and had good luck. Maybe you'll get lucky.

    Lee's Machinery - Industrial Company - Perry, Ohio |...
  21. He forgot to post the pic of that 1950's American.

    He forgot to post the pic of that 1950's American.
  22. Replies
    154
    Views
    24,319

    For a young guy, he's got it together........even...

    For a young guy, he's got it together........even if he's a politician.
  23. Replies
    8
    Views
    1,146

    Daniel, The first thing I'd try is to give it a...

    Daniel,
    The first thing I'd try is to give it a taste of ether. Might help you rule out a few things. Mine is older than yours, so I'm not familiar with those control valves. Oh, it's in the mail....
  24. Replies
    3
    Views
    710

    I guess it would be okay for wood, but at 10/12...

    I guess it would be okay for wood, but at 10/12 thou. rpm on steel........not so good!
  25. Replies
    7
    Views
    805

    Gordon The R model has separate clutches Tom...

    Gordon
    The R model has separate clutches

    Tom
    For every word I type I discovered if I add another letter then backspace then use the space bar I create a space. Comp is screwed up
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4