Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mtndew

Page 1 of 60 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    3
    Views
    387

    Yes. We have a variety of these and they cover a...

    Yes.
    We have a variety of these and they cover a lot of different threads.
    LakeShore Carbide.com Carbide End Mills-Carbide Thread Mills - SINGLE PROFILE THREADMILLS
  2. Uh no. That is far from being the problem here....

    Uh no. That is far from being the problem here.
    How are you holding on to the end mill, how much is sticking out?
    I'm inclined to think that something is at play in your spindle as said earlier...
  3. How long is the slot? How deep is the slot? ...

    How long is the slot?
    How deep is the slot?


    And like Spruewell said, do not use an end mill with more than 3 flutes for roughing in this scenario.
  4. Replies
    8
    Views
    551

    Simple trigonometry will give you that answer.

    Simple trigonometry will give you that answer.
  5. Replies
    17
    Views
    1,202

    I didn't know you could weld cast iron, I've only...

    I didn't know you could weld cast iron, I've only seen it brazed.
    Learn sumptin new everyday.
  6. Replies
    19
    Views
    957

    Just remember, when designing a part, the...

    Just remember, when designing a part, the prettier it looks the more it's gonna cost.
    Put a small edge break where needed to get rid of sharp edges, and a larger chamfer where needed for...
  7. Replies
    19
    Views
    957

    I assume you're talking about outside edges, then...

    I assume you're talking about outside edges, then yes chamfers are typically the easier of the two because cutting fillets on outside edges requires a corner rounding form tool or a 3D toolpath....
  8. Replies
    12
    Views
    490

    It's not carbide, it's HSS. It's also nothing...

    It's not carbide, it's HSS.
    It's also nothing special, it could have been used in a lathe or maybe even a shaper.
  9. Replies
    217
    Views
    9,552

    Fixed for accuracy.

    Fixed for accuracy.
  10. Replies
    27
    Views
    1,280

    Man I miss cutting that stuff on the lathe.

    Man I miss cutting that stuff on the lathe.
  11. Replies
    31
    Views
    1,327

    I've had 2 sets of Mitutoyo telescoping gages...

    I've had 2 sets of Mitutoyo telescoping gages back in the 90's when I was running engine lathes. They are complete garbage. Bought a set of Starrett telescoping gages and still have them. Maybe the...
  12. Replies
    217
    Views
    9,552

    You're really not helping your case, and to be...

    You're really not helping your case, and to be honest I think you're way past that point.
  13. Thread: Doosan DNM4000?

    by Mtndew
    Replies
    31
    Views
    1,519

    I think he said that the machine will run just...

    I think he said that the machine will run just aluminum, not necessarily only these parts.
    Either way, get TSC from the factory, you wouldn't want to have it put on later and realize that it's a lot...
  14. Put that same line of code in MDI and run it,...

    Put that same line of code in MDI and run it, what happens?
  15. Replies
    217
    Views
    9,552

    True, but new people that come into this site see...

    True, but new people that come into this site see his constant shitposting will see it and IMO it's a bad look for PM. He can't just run amuck, it needs to be dealt with by the mods.
    Call it...
  16. Replies
    4
    Views
    478

    Dura Bar 201 Ni Resist machinability

    Anyone ever cut this stuff?
    I've cut lots of "regular" dura bar cast iron over the years, is this similar? Or is it a mofo?

    EDIT:
    I just found a site that says it has a 135% machinability...
  17. Thread: Fanuc 6T Post

    by Mtndew
    Replies
    16
    Views
    910

    So.... why don't you call them and get it sorted...

    So.... why don't you call them and get it sorted out?
  18. Replies
    24
    Views
    2,170

    Maybe they're banking on the new swissmak ez...

    Maybe they're banking on the new swissmak ez button software coming out soon and wanna scoop that up.:popcorn:
  19. Replies
    24
    Views
    2,170

    Head them off at the pass? I hate that cliche` ...

    Head them off at the pass? I hate that cliche` ~ Hedley Lamarr

    We'll head them off at the pass - YouTube
  20. As long as you tell it your values accurately...

    As long as you tell it your values accurately it's perfect. It's all math related (to put it mildly) and it does all the work for you.
  21. Show me on the doll where Sandvik touched you....

    Show me on the doll where Sandvik touched you.
    lol
    I will give it to Iscar for grooving though, I've always preferred their grooving line.
    But saying they suck in comparison is completely false.I...
  22. My vote is for Sandvik. Their product line is...

    My vote is for Sandvik. Their product line is tough to beat, and if you have a good rep you can get a pretty good discount from the list price.
  23. Bye Felicia.

    Bye Felicia.
  24. Replies
    317
    Views
    16,880

    Hah! When all else fails, play the victim card!

    Hah! When all else fails, play the victim card!
  25. Replies
    23
    Views
    1,811

    Why? I can see if you're running a $50k...

    Why?

    I can see if you're running a $50k machine,but a Multus? :willy_nilly:
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4