Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Illinoyance

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    385

    Everything you need to know about grates. Neenah...

    Everything you need to know about grates.
    Neenah Foundry | Metal castings proudly made in the USA
    Made from cast iron, ductile iron, galvanized steel.
  2. Re: drilling case hardened shaft. Straighten...

    Re: drilling case hardened shaft.
    Straighten after drilling if necessary.
  3. Replies
    20
    Views
    939

    Instead of tapped holes can you use through bolts...

    Instead of tapped holes can you use through bolts with nuts and hard washers under the plate? The greater length of bolt under preload will give more consistent clamping load for the fixture. I am...
  4. Replies
    7
    Views
    454

    I had a cooler vest with a vortex tube to provide...

    I had a cooler vest with a vortex tube to provide cooling. It worked extremely well but required a lot of compressed air. With the local humidity being high there was a problem with condensate...
  5. Replies
    4
    Views
    534

    A quick internet search would have revealed the...

    A quick internet search would have revealed the products are totally unrelated.
  6. Replies
    3
    Views
    512

    When the grinder is at rest any coolant that is...

    When the grinder is at rest any coolant that is absorbed by the wheel tends to collect at the bottom of the wheel resulting in imbalance. Jogging the spindle a couple time throws the absorbed...
  7. Sopko has them. Becaue Delta uses an odd size,...

    Sopko has them. Becaue Delta uses an odd size, expect to pay accordingly.
  8. Replies
    38
    Views
    1,871

    It pisses me off when someone asks for...

    It pisses me off when someone asks for information on this forum when he could have gotten the answers from a quick internet search.
  9. C45 is weldable with proper preheat and post...

    C45 is weldable with proper preheat and post heat. I can't be more specific because I gave away all my welding reference materials. Here is where to look:
    Welding Preheat Calculator
  10. Improve your possibilities by considering a W...

    Improve your possibilities by considering a W section with equal or higher section modulus and moment of inertia as the S beam.
  11. Forget the mill. Make a template that locates on...

    Forget the mill. Make a template that locates on the center hole. Cut with plasma.
  12. If it is gummed up with dried coolant I suggest...

    If it is gummed up with dried coolant I suggest soaking in boiling water. That worked for me when I had a seized up Tenthset boring head.
  13. Replies
    5
    Views
    976

    Could you measure the timing belt pulleys and get...

    Could you measure the timing belt pulleys and get the part number for each belt. The power drive components are missing from mine. Thanks.
  14. Replies
    15
    Views
    1,030

    Roll a cylinder from sheet.

    Roll a cylinder from sheet.
  15. Replies
    13
    Views
    1,914

    Check with Brownells. Their 3.5% nickel rod is...

    Check with Brownells. Their 3.5% nickel rod is supposed to take color case hardening.
    BROWNELLS 3 1/2% NICKEL STEEL WELDING ROD | Brownells
  16. With that hole below the spindle I would say that...

    With that hole below the spindle I would say that is the base for a reamer grinding attachment. The rod projecting from that hole would have mounted a dead center. As to the fix of the broken...
  17. I have a couple spa pumps with 2 speed motors I...

    I have a couple spa pumps with 2 speed motors I want to get rid of.
  18. Replies
    2
    Views
    416

    There is a wealth of information in these old...

    There is a wealth of information in these old books. Much of it has been forgotten.
    Thanks for the link.
  19. These are near what you want. Thin Parallels, 3"...

    These are near what you want.
    Thin Parallels, 3" Long, 11 Pairs 3946 - LittleMachineShop.com
  20. Replies
    4
    Views
    1,235

    Try here:...

    Try here:
    https://www.leevalley.com/en-us/shop/general/catalog/47025-hardware-catalog
  21. The micrometer works even better is held in a...

    The micrometer works even better is held in a stand.
  22. You need a 5C fixture mount. Victor Machinery -...

    You need a 5C fixture mount.
    Victor Machinery - Metalworking tools and supplies
  23. Coparator stand with dial indicator or snap gauge.

    Coparator stand with dial indicator or snap gauge.
  24. I would like to see a photo of the Atlas X-Y...

    I would like to see a photo of the Atlas X-Y rotary table.
  25. Don't even try to remember it. Get it on paper...

    Don't even try to remember it. Get it on paper or bookmark a web page. If I recall Machinery's Handbook has that info. Make up a binder of frequently needed information.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4