Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hardplates

Page 1 of 13 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    499

    What is the machine? Round cutters have a lot of...

    What is the machine? Round cutters have a lot of engagement and I have found they like a heavy cut = need a rigid machine and setup.
  2. Try Alro. I used to weld literally tons of inco...

    Try Alro. I used to weld literally tons of inco 625, what do you want to know?
  3. Replies
    9
    Views
    3,360

    Anyone know if this was ever resolved or have an...

    Anyone know if this was ever resolved or have an idea? I'm looking at making an offer on a Lico that has a similar problem and trying to base my offer off how difficult I think it will be to fix.
  4. $225 shipped flat rate

    $225 shipped flat rate
  5. Replies
    2
    Views
    241

    I don't know how you found that but thank you!!!!!

    I don't know how you found that but thank you!!!!!
  6. Replies
    51
    Views
    3,195

    Def a VMC, I could survive without one, but I...

    Def a VMC, I could survive without one, but I would have a tough time making any money.
  7. Big work goes in big chuck and spins slowly,...

    Big work goes in big chuck and spins slowly, small work goes in small chuck and spins quickly. End of story. I have a lathe that came with several chucks new and the 4 jaw and largest 3 jaw and...
  8. Replies
    2
    Views
    241

    Valenite 539.69.646 Facemill ID?

    A friend of mine gave me a Valenite 539.69.646 facemill. It appears to be in good shape and I am thinking about putting it into service but I can't find anything about it anywhere. Does anyone have...
  9. Don't threaten me with a good time.

    Don't threaten me with a good time.
  10. Replies
    508
    Views
    33,571

    :fight: :D

    :fight: :D
  11. Replies
    508
    Views
    33,571

    YouTube...

    YouTube

    There was nothing wrong with the radio
  12. At least its a fellow Pa spammer :typing:

    At least its a fellow Pa spammer :typing:
  13. Replies
    508
    Views
    33,571

    I can't be old yet, I havith no wisdom.... yet....

    I can't be old yet, I havith no wisdom.... yet. Speak for yourself grandpa :codger:
  14. How thick? If you mean its a blind pipe flange...

    How thick? If you mean its a blind pipe flange that's 3" od I would assume its for around 1" pipe. Depending on how many pound flange it is maybe 1/2" to 5/8" thick?

    If that's the case I would...
  15. Replies
    29
    Views
    1,101

    They still make those? :sulk:

    They still make those? :sulk:
  16. Replies
    508
    Views
    33,571

    Oh my, I was just getting ready for high school...

    Oh my, I was just getting ready for high school :reading:
  17. Replies
    508
    Views
    33,571

    I would be far more interested in ultimate...

    I would be far more interested in ultimate tensile and yield than a Charpy test. How about a basic hardness test? Start simple right? While I would assume they are within hardness spec it always pays...
  18. Replies
    508
    Views
    33,571

    Little reliable data is obtained with a thumb...

    Little reliable data is obtained with a thumb detector. Also that is applying radial load which would be far more reliable to do with a long bar, pull gauge and some math.

    I would be far more...
  19. Thread: Big-plus

    by Hardplates
    Replies
    16
    Views
    993

    I often run big plus holders in a standard...

    I often run big plus holders in a standard spindle and there is a gap. It is my understanding that to make contact both the spindle and holder mating surfaces are moved closer to eachother….. Maybe...
  20. Replies
    508
    Views
    33,571

    There is no doubt that sounds like an aggressive...

    There is no doubt that sounds like an aggressive setup.

    I find failure analysis fascinating.

    Here is my 3 worthless cents.

    The manufacturer should be given the opportunity to do their own...
  21. Replies
    508
    Views
    33,571

    I am in no way taking sides and have been pleased...

    I am in no way taking sides and have been pleased with every Maritool product I own. I do find it interesting that it didn't fail at the smallest cross section. I was under the impression that...
  22. I'm gonna call BS on that. Sounds like a BS...

    I'm gonna call BS on that. Sounds like a BS excuse for not fixing it. If it actually is true its a counter productive stupid idea. It would make you more likely to cut undersize cause you would be...
  23. Replies
    508
    Views
    33,571

    It's very difficult to tell in the pictures but...

    It's very difficult to tell in the pictures but the grain structure at the break looks kind of large......maybe. A metallurgist or heat treat expert could likely tell with a quick glance in person. I...
  24. Thread: Big-plus

    by Hardplates
    Replies
    16
    Views
    993

    Yes they will work but won't engage the spindle...

    Yes they will work but won't engage the spindle face.
  25. Thread: Big-plus

    by Hardplates
    Replies
    16
    Views
    993

    So I have heard. I have some Big Plus holders but...

    So I have heard. I have some Big Plus holders but nothing with a Big Plus spindle. I've often though about removing the drive keys and making a ring with integrated dogs so the ring engages the...
Results 1 to 25 of 322
Page 1 of 13 1 2 3 4