Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CalG

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. That IS the definition of ignorance. To know the...

    That IS the definition of ignorance. To know the truth, and reject it. You even use the word ignore to describe their actions.

    IGNORANCE

    Agenda promoting dipwards! Can't trust them to do...
  2. Atlas shaper offered in VT craigslist tool section

    It's cute.

    I know nothing of them, and do not have any interest. But if someone was wanting a small shaper....Check out the listing.

    Living close to Montreal would shorten the drive ;-)

    ...
  3. Refinish? Strip the old finish with chemical...

    Refinish? Strip the old finish with chemical stripper prior to sanding regardless of paper type.
    You will be money and time ahead.

    Oh, Alox is fine. It lasts a long time on bare wood.
  4. Replies
    19
    Views
    2,283

    Dual Head Air Chuck Washer | Milton Industries...

    Dual Head Air Chuck Washer | Milton Industries
  5. Replies
    7
    Views
    635

    I believe, IF the motor is incapable of...

    I believe, IF the motor is incapable of reversing, the case drain can tie to the return line. Call it "less than 200psi"

    That is a valving determination for the application. If the motor EVER...
  6. One can NEVER have all the accessories you need...

    One can NEVER have all the accessories you need ;-)
  7. I would like to find a B945 Tilting table. I...

    I would like to find a B945 Tilting table. I have the mounting base.
  8. Replies
    13
    Views
    763

    It's too much to keep up with all the different...

    It's too much to keep up with all the different equipment. Check with the distributor for better assurance.

    ETA

    Reading through the manual, That drive looks like a good one. But I'm no...
  9. I would have a hard time justifying the trouble...

    I would have a hard time justifying the trouble to pick up most of that tooling.

    I've got a great Wade 94, so the Harding, though it catches my eye, is just something that needs cleaning.
    ...
  10. Does the entire extended section rotate on these...

    Does the entire extended section rotate on these units? Or is that a supporting sleeve that is fixed to the body and carries bearings?
  11. A useful visual Bleed Down Resistors -...

    A useful visual

    Bleed Down Resistors - Capacitors - Product Guides
  12. Replies
    13
    Views
    763

    I have run the shop 7 hp air compressor on a 20hp...

    I have run the shop 7 hp air compressor on a 20hp Toshiba TOSVERT VFD for over ten years. It works great. I appreciate the soft start the most.
    The Toshiba line offers easy parameter settings from...
  13. Or stone tiles. My favorite. 5-3/4" square. ...

    Or stone tiles. My favorite. 5-3/4" square. Makes for a nice transition from one space to another.
  14. Just use the number of caps that get the idler...

    Just use the number of caps that get the idler spinning (the same way every time. Some motors start very easily.

    A 2 watt resistor is enough to bleed off a charge . no need to be in a hurry.
  15. I could see that part being spun to near net, ...

    I could see that part being spun to near net, then ground on the inside (The apex would be a byt##)

    Mounted on a formed mandrel to finish grind the outside.

    Not too bad, maybe a $700 part...
  16. My, those projections sure look a lot like...

    My, those projections sure look a lot like static wicks on the trailing surfaces of airplane wings ;-)

    Some of us A&Ps called them "static dissipation wicks". Bleeding the charge off the...
  17. Is this a case where the VFD carrier frequency...

    Is this a case where the VFD carrier frequency caused movement in the windings that resulted in random wire to wire shorts through the wire varnish insulation?

    That would be consistent with near...
  18. My wife and I took a rather pleasant ride through...

    My wife and I took a rather pleasant ride through the S.Vt countryside today on my 1999 VFR800fi. The last year of the gear! ;-)

    It's a pretty nice bike., and I find pleasure in just listening...
  19. Replies
    3
    Views
    639

    Before the customization, I could see that...

    Before the customization, I could see that apparatus corking wine bottles. ;-)
  20. Bill None of those examples of surrendered...

    Bill

    None of those examples of surrendered freedoms you have listed relate to the preservation of "Life liberty and Happiness". Endowed by our creator.

    Nor do they offer any mechanism to...
  21. I'm with JST on all comments. I also ran a...

    I'm with JST on all comments.

    I also ran a Logan 12 inch with an 8 inch Buck Adjust true. I plug reversed that thousands of times with no issues after merely spinning the chuck on with a gentle...
  22. It appears to go back to the sentiment expressed...

    It appears to go back to the sentiment expressed in post #3
  23. Replies
    8
    Views
    674

    second forming tool had significant loss of...

    second forming tool had significant loss of contact mass which possibly
    allowed improved radius in workpiece--russian language barrier in narration
    is a handicap here

    my impression of russian...
  24. If you don't go molded... parts on a side link...

    If you don't go molded...

    parts on a side link only conveyor indexed to a stiff lifting bottom plate that references on the part's center though hole and the two c'bores, a matching top plate...
  25. Replies
    8
    Views
    674

    I will need to try this with mild steel. The SS...

    I will need to try this with mild steel. The SS may be easier due to thermal conductivity.

    Do you know the reason for "changing tools"? Roughing and finishing?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4