Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ox

Page 1 of 60 1 2 3 4

Search: Search took 0.12 seconds.

  1. Well, that would be a bulky tool for bone screws,...

    Well, that would be a bulky tool for bone screws, so ...
    (same principal as whirling)


    ----------------

    Think Snow Eh!
    Ox
  2. Replies
    295
    Views
    74,725

    I get a feeling that he would rather be in the...

    I get a feeling that he would rather be in the condition to use those tools.

    I doubt that I would like to trade him places.

    ???


    ------------

    Think Snow Eh!
  3. That's the point that came to my mind. With a 4...

    That's the point that came to my mind.
    With a 4 caster set-up, there will always be 2 taking the lions share of the weight , and the opposite 2 just keeping it upright.
    So - might want to consider...
  4. But wouldn't they hold the camera upside down...

    But wouldn't they hold the camera upside down there too?
    Shirley their camera's may use gravity - and not a compass?


    Actually that tool doesn't look to have a top or bottom.
    Must be more for...
  5. Shirley that tool is upside down, no? ...

    Shirley that tool is upside down, no?


    -------------------

    Think Snow Eh!
    Ox
  6. Crankshaft? ------------------------ ...

    Crankshaft?


    ------------------------

    Think Snow Eh!
    Ox
  7. Replies
    464
    Views
    27,943

    In all honesty - if you are using a Brother in...

    In all honesty - if you are using a Brother in the high volume app that they are built and marketed for, finger CAMing in a few M codes here and there shouldn't be a hardship.

    ...
  8. What does a person run a cutter like that in? A...

    What does a person run a cutter like that in?
    A large Hydrotel?


    --------------------

    Think Snow Eh!
    Ox
  9. Replies
    21
    Views
    834

    While I will say that these things are the real...

    While I will say that these things are the real deal when comparing to "plastic" trays, we must use a fair amount of depleted uranium here?

    And yes - you can stack them several tiers tall all day...
  10. Replies
    13
    Views
    503

    Yeah, but you couldn't justify 3 new 6 figure...

    Yeah, but you couldn't justify 3 new 6 figure positions in the office to annalize info if you bought a 2" gage line holder....


    -----------------

    Think Snow Eh!
    Ox
  11. Replies
    13
    Views
    503

    Intelligent Toolholders

    Have you seen this yet?

    I found this in the current issue of Manufacturing News, but I wasn't able to quickly find a way to find this article there, so - off to the Horse....

    Now - while there...
  12. You only have 1 tool per? Or will it...

    You only have 1 tool per?
    Or will it automatically pick up one certain offset, and if you want another you need to MDI?


    I'm sure that it [again] is MTB specific - as it most anything - but -...
  13. Replies
    464
    Views
    27,943

    Good grief, what year is that? ...

    Good grief, what year is that?


    -----------------

    Think Snow Eh!
    Ox
  14. Replies
    21
    Views
    834

    https://i.pinimg.com/originals/26/14/86/2614866253...

    https://i.pinimg.com/originals/26/14/86/2614866253cb9f9a4421695345b41638.jpg


    -------------

    Think Snow Eh!
    Ox
  15. My bad, I was thinking more along the lines of...

    My bad, I was thinking more along the lines of "prepare" an egg.
    You did specify "cook".

    :o


    -----------------

    Think Snow Eh!
    Ox
  16. Replies
    21
    Views
    834

    I have hundreds of these. I like them. They are...

    I have hundreds of these.
    I like them.
    They are fiberglass and have a wire embedded around the top rim.
    They are quite solid.
    Stack and nest
    ...
  17. Replies
    4
    Views
    389

    Have you exhausted the possibility that someone...

    Have you exhausted the possibility that someone may already make a very similar product already?

    Like Titex, or Guering, or OSG?
    (I'm sure oodles more)

    These company's doo already make some...
  18. Rocky only has one? ----------------- ...

    Rocky only has one?


    -----------------

    Think Snow Eh!
    Ox
  19. Replies
    464
    Views
    27,943

    While we're currently discussing the bounty's of...

    While we're currently discussing the bounty's of these machines in stead of the limits:

    2/3 says 1.2 (1.4?) sec chip to chip, and I'm ass_u_ming that is for adjacent tools.

    How much longer if...
  20. Replies
    464
    Views
    27,943

    Well then, can we discuss how a fella is s'posed...

    Well then, can we discuss how a fella is s'posed to know if his tension is OK or not if he doesn't know what it's s'posed to be in the firth place?
    I'm amazed that this would be a guarded secret in...
  21. I'm still not following where the problem lies? ...

    I'm still not following where the problem lies?

    What is the point in having an offset active or not if you are setting (probing?) your new tool?
    Aren't you simply going to index to that position...
  22. Replies
    25
    Views
    1,401

    What if you break the head off and the shank is...

    What if you break the head off and the shank is down in there yet?
    I'd guess that it is now loose and should back right out?


    ------------------

    Think Snow Eh!
    Ox
  23. I use T0 all the time in program - like almost...

    I use T0 all the time in program - like almost every tool change.
    On my Fanuc AND my Mits lathes.
    I call T0 and send X to a known safe index location. (X15. / X17.)

    I have up to 4 different...
  24. Thread: B&A Precision

    by Ox
    Replies
    5,249
    Views
    804,070

    It's your other left. -------------------- ...

    It's your other left.


    --------------------

    Think Snow Eh!
    Ox
  25. Replies
    25
    Views
    1,401

    I've wondered how those type cutter were. Not...

    I've wondered how those type cutter were.
    Not seen much talk about them in the past.

    I would think that any product brought to market would be pretty good - otherwise they just wouldn't sell -...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4