Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: DMF_TomB

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    4
    Views
    94

    . often taper pin can be difficult to get out....

    .
    often taper pin can be difficult to get out. backlash can come from the collars holding shaft and can come from nut that is loose on worn screw. often middle of travel is loose and ends of travel...
  2. countries and states that give tax breaks and not...

    countries and states that give tax breaks and not much different than 2 unions competing with one another where there locations overlap. kind of hard to ask for $40./hr when a different union only...
  3. Replies
    16
    Views
    905

    industrial air compressors and i am talking...

    industrial air compressors and i am talking 1000hp or higher have yearly maintenance done. there are check valves sometimes called reed valves that i have taken apart and replaced broken springs.
    ....
  4. businesses get tax breaks and other benefits...

    businesses get tax breaks and other benefits based on where they are. tariffs, taxes, labor rates, anti pollution requirements all have effects.
    .
    many many times a country or state will cry about...
  5. Replies
    13
    Views
    833

    i would use . mineral spirits . then alcohol...

    i would use
    .
    mineral spirits
    .
    then alcohol wiping
    .
    then sand 50 grit sandpaper
    .
    then alcohol wipe til wiper tissues come off clean. til the dirt is off it aint clean yet. might take 10...
  6. when i want epoxy to stick to cast iron i rough...

    when i want epoxy to stick to cast iron i rough it up with 50 grit sand paper so it has something rough enough to grab
    .
    pickling or acid treatment may be roughing the surface too
  7. Replies
    13
    Views
    711

    . only thing to add is i use a .001 or .002"...

    .
    only thing to add is i use a .001 or .002" smaller pin in a hand tightened collet so if hole not aligned it just pushes pin into collet. normally to get pin close and handle mode adjust you can...
  8. its my belief those pan types are never really...

    its my belief those pan types are never really fully cleaned. that is you leave some fat and oil thats charred on the surface, and after a few dozen times of use its seasoned. if a few spots flake...
  9. Replies
    20
    Views
    901

    i have scanned negatives before (with a slide...

    i have scanned negatives before (with a slide light box to shine light through it) but dont expect miracles. my old company had all microfilm drawings scanned to tiff files.
    .
    bulk scanning by the...
  10. Replies
    5
    Views
    593

    horizontal cnc's that share 24 pallets (44"square...

    horizontal cnc's that share 24 pallets (44"square tables) that a robot is used to put in racks with parts (parts often weigh over 1/2 ton) in fixtures on pallets or load pallet on to cnc or bring to...
  11. Replies
    20
    Views
    901

    a slide light box if placed over negative will...

    a slide light box if placed over negative will shine light through it for scanning.
    .
    typical film resolution. if you take average 35mm camera with average high quality lenses and tried to...
  12. Replies
    12
    Views
    732

    i have seen triple sealed ball bearings before,...

    i have seen triple sealed ball bearings before, used to call them farm or manure bearings, hard to turn but triple seals helps keep the dirt from getting in on tractors and stuff. got to make sure...
  13. Replies
    37
    Views
    2,732

    . the parameter where rapid stops and feed...

    .
    the parameter where rapid stops and feed begins when pecking back into hole is important. if peck drilling with a spade drill or any drill type and if hearing crunching sound when it rapids back...
  14. Replies
    37
    Views
    2,732

    . long parabolic drills are famous for vibration...

    .
    long parabolic drills are famous for vibration resonance issues. that is rpm often has nothing to due with a cutting edge heat limit. often have seen where vibration was ignored cause feed and...
  15. Replies
    12
    Views
    732

    load of application has a effect. that is when...

    load of application has a effect. that is when soft materials are used for bearings under high load they tend to distort, flow or wear out extremely fast. often dont last even a week if psi or load...
  16. had a mazak rotary union go. it sounded like a...

    had a mazak rotary union go. it sounded like a machine gun as the ball bearings went out of it. then coolant was leaking around tool changer arm and got on encoder so tool changer arm went out of...
  17. Replies
    37
    Views
    2,732

    . if some chips still in hole and if peck into...

    .
    if some chips still in hole and if peck into hole goes too close to hole bottom when you rapid 100% the chips get pushed to hole bottom compressed hard and its like drill hit part with a hammer....
  18. Replies
    9
    Views
    815

    many parts are lapped with a thin lapping...

    many parts are lapped with a thin lapping compound and rotated and moved back and forth lengthwise then they are cleaned of lapping compound. glass lenses are called ground but its a type of lapping...
  19. Replies
    46
    Views
    3,014

    usually a probe will repeat within .0002"...

    usually a probe will repeat within .0002" assuming it doesnt have sticky residue on probe tip or there is no dirt on the part measured. or there is no sticky residue in the probe. i have seen probes...
  20. Replies
    37
    Views
    2,732

    basis math lets say per 100 parts at 3 minutes...

    basis math lets say per 100 parts at 3 minutes each not pecking and 6 minutes pecking
    .
    660 minutes actual total per 100 parts, 300 minutes + 360 minutes rework (2% of parts break drills) plus a...
  21. Replies
    37
    Views
    2,732

    broke a .166 drill today, only going about 1.1"...

    broke a .166 drill today, only going about 1.1" deep, still no peck and it broke about 1" deep into the 1st hole. took about 3 hours to drill it out and replace drill and rerun and replace tap that...
  22. Replies
    37
    Views
    2,732

    . obviously you use what works best. ....

    .
    obviously you use what works best.
    .
    pecking is not fool proof. it does have certain factors that need to be aware off. for example pecking and rapids are so fast the coolant does not have...
  23. Replies
    19
    Views
    924

    gear making machine manufacturers have ways to...

    gear making machine manufacturers have ways to design, machine, hone, grind, lap and test gears extremely fast. the technology is fairly complex and many manufacturers have training classes. and many...
  24. Replies
    37
    Views
    2,732

    i peck often even with spade drills (easily over...

    i peck often even with spade drills (easily over 1000 spade drilled holes) and other drills that some say never to peck with
    .
    obviously and maybe needs to be emphasized a billion times you usually...
  25. Replies
    1
    Views
    334

    sometimes a special round plate with shoulder...

    sometimes a special round plate with shoulder sits tightly in the large bore and this plate has a center hole that a shaft also with a shoulder goes into. the shaft sticks up centered on the locating...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4