Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Milland

Page 1 of 60 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    9
    Views
    1,033

    It's a mini spindle speeder: YouTube...

    It's a mini spindle speeder: YouTube
  2. So you proved you could save an opp by...

    So you proved you could save an opp by eliminating the pre-drilling...
  3. Replies
    24
    Views
    1,515

    I think we need a diversionary tactic before we...

    I think we need a diversionary tactic before we have a fraternal war.

    Look, over there! A squirrel!!
  4. Rigid machines will typically allow you to cut...

    Rigid machines will typically allow you to cut harder and faster with the same tool life as a "flexy" mill, or cut the same speed with a longer lasting tool. Better side taper too, and usually (as...
  5. Replies
    6,083
    Views
    180,983

    Yes, despite my adding a little humor to some of...

    Yes, despite my adding a little humor to some of the comments I am hoping he's OK. Was a frequent poster up until May...
  6. Replies
    24
    Views
    1,515

    My new theory is that he was bitten by a...

    My new theory is that he was bitten by a radioactive spider, and is now sitting in the middle of a web inside of Big Ben.
  7. Replies
    55
    Views
    2,641

    Psst: It's actually a shrink holder... :D

    Psst: It's actually a shrink holder... :D
  8. Replies
    24
    Views
    1,515

    I sit corrected. That's good, but still begs the...

    I sit corrected. That's good, but still begs the question of why he buggered off.
  9. Replies
    24
    Views
    1,515

    That would be nice. I hope someone out there has...

    That would be nice. I hope someone out there has an address.
  10. Replies
    22
    Views
    730

    Your "material" rating will change with post...

    Your "material" rating will change with post count, it's not otherwise adjusted.

    For your inserts, I have no idea if they're optimal for steels at the speeds you'd like to go, or if they're being...
  11. Replies
    24
    Views
    1,515

    Hey, I'm a Peasant-American, and I strongly...

    Hey, I'm a Peasant-American, and I strongly object to being objectified as a less-than-magnificent specimen of humanity!! I'm contacting my lawyer and my human rights advocate!

    Back on topic -...
  12. Replies
    24
    Views
    1,515

    OT-ish - is Adama OK?

    Hi all,
    Just wondering how Adama's doing, he's been quiet on the site since mid-May. I pm'd one of the British members (Limy Sami), but he's heard nothing either.

    Hope he's just busy, or the...
  13. Replies
    12
    Views
    894

    Interesting. Do you have a link that gives...

    Interesting. Do you have a link that gives access to the remaining chapters of that treatise?
  14. Replies
    55
    Views
    2,641

    It's like the Garr copywriter didn't believe the...

    It's like the Garr copywriter didn't believe the engineer's suggestions, and added an extra "0" to the IPT values.
  15. Thread: 2015 Haas VM-3

    by Milland
    Replies
    9
    Views
    712

    Unless Mr. Geek is a supporter of the site, he's...

    Unless Mr. Geek is a supporter of the site, he's basically just spamming his wares. I reported both his morning listings, but they seem to hang around.
  16. Replies
    3
    Views
    310

    To save others the trouble - reported. And in...

    To save others the trouble - reported.

    And in this case - if it's named after a bird, it's a duck. And if it's a duck, it's spam. A Spamducken, if you will...
  17. At that cost I'd just buy a pair of new TRAK bed...

    At that cost I'd just buy a pair of new TRAK bed mills.

    Check out Centroid, and you might also look for threads on the CNC Zone, they tend to be more focused on conversions and the like.
  18. Sending you an email...

    Sending you an email...
  19. Replies
    23
    Views
    1,597

    Not knowing for certain, but: 1) Bottom thread...

    Not knowing for certain, but:

    1) Bottom thread anchors in block (as shown above)

    2) Middle thread (and nut) clamps cylinder barrel flange to block

    3) Upper thread (and nut) clamps head to...
  20. Replies
    101
    Views
    7,000

    What are the advantages of the Heidenhain control...

    What are the advantages of the Heidenhain control over the Fanuc?
  21. Replies
    35
    Views
    1,836

    IMO you shouldn't see over .0005" per side on a...

    IMO you shouldn't see over .0005" per side on a 2" depth with a sharp 1/2" carbide endmill doing a finish cut 2" deep in Al. But that can vary with tooth count, speed, etc.

    If your Z is moving,...
  22. Replies
    49
    Views
    3,141

    That worked fine, and it looks like your machine...

    That worked fine, and it looks like your machine does not have a transmission. I wonder if someone tried entering parameters that show a trans present - that could account for the incorrect error...
  23. Replies
    35
    Views
    1,836

    50lbs is enough to show a deflection that's...

    50lbs is enough to show a deflection that's greater in one direction than another. It just shows the trend. The actual "pushing force" of an endmill varies (of course), but under finish conditions...
  24. Replies
    35
    Views
    1,836

    All machines deflect, but isolating where it's...

    All machines deflect, but isolating where it's happening can be time consuming. I'm a little confused that you'd spend all that money and effort on an old Haas, but IIWII...

    First thing I'd check...
  25. Replies
    49
    Views
    3,141

    Can you try to post (or link to) a larger, better...

    Can you try to post (or link to) a larger, better picture? This one's a bit small...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4