Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: lectrician1

Page 1 of 34 1 2 3 4

Search: Search took 0.01 seconds.

  1. It was a pleasure. Thank you for the kind words....

    It was a pleasure. Thank you for the kind words.
    Rich
  2. accurate DRO is SOLD! Thanks

    accurate DRO is SOLD! Thanks
  3. isn't there a cover on the tailstock end that is...

    isn't there a cover on the tailstock end that is removable to see the generator?
    also make sure the variable speed knob on the bottom left, is not turned all the way counter clockwise. put it...
  4. make sure the generator is spinning in the...

    make sure the generator is spinning in the correct direction.
  5. Shipping 5 pound package to canada usps $54.95...

    Shipping 5 pound package to canada usps $54.95
    fedex $44.65
    I would go fedex.
    PM if you want it
  6. ok ill get a shipping estimate

    ok ill get a shipping estimate
  7. Dynasty SOLD! Thank you

    Dynasty SOLD! Thank you
  8. Heidenhain DRO display NDP 960 3 axis $350 plus ship

    I have this Heidenhain NDP 960 3 axis DRO display I dont need.
    Works fine

    Down load manual on Heidenhain site

    Takes 9 pin round connectors

    3 axis. I had this on my mill until I replaced it...
  9. here is a pic of the connector 324317

    here is a pic of the connector


    324317
  10. Heidenhain DRO DISPLAY VRZ 653 $75 PLUS SHIP

    This is a panel mount display but you could probably mount it on an arm.

    Three axis with memofix. I'm not sure what the memofix is for.

    Display powers up looks good. I cannot test it further.
    ...
  11. Acu-rite DRO display quikcount II $20 plus ship

    This old school display powers on.
    Perfect if you have this system and need a backup display.
    No scales just the display

    It takes the 6 pin round connector

    $20 plus flat rate usps shipping. ...
  12. Thank you to all the folks who helped with the...

    Thank you to all the folks who helped with the postage via paypal. Thanks to the person who sent a $5 bill in the mail. I got it!
  13. Well I'm about to button things up. Lathe is...

    Well I'm about to button things up. Lathe is running great. I will run it for a couple weeks to make sure everything stays status quo. Thanks everyone for all the help.
  14. voltage across e1 and e2- 116v with the spindle...

    voltage across e1 and e2- 116v with the spindle off
    spindle on: voltage raises slightly to around 118 and stays there loaded or unloaded.
  15. more nonsense you know all your posts are...

    more nonsense
    you know all your posts are blocked on my PM page
    I have blocked your posts for close to two years. Just because I grew tired of having to read paragraph after paragraph of nothing....
  16. I wish you could just answer the question

    using another tachometer the gen is spinning near 3600 and the exciter is the same

    Thermite, when you give answers like this, it is a nuisance to even read through them.

    question: "At what rpm...
  17. Ok John, Kevin, and Jerry your magnifiers will go...

    Ok John, Kevin, and Jerry your magnifiers will go out today.

    Sorry to say I have none left. All gone. I'm keeping three for future machines

    If anyone needs one just go on Amazon and buy 60 for...
  18. at what rpm should the ac motor be running? ...

    at what rpm should the ac motor be running?

    what would you call a substantial cut, in thousandths with feed and rpm?
  19. I thought if the spindle is off, the voltage on...

    I thought if the spindle is off, the voltage on F1 and F2 is the supposed to be 115v if I'm at around 700rpm on the rheostat.
    I'll check e1 and e2 at the terminal box tomorrow. thanks
  20. I matched the two pulleys which slowed the...

    I matched the two pulleys which slowed the exciter speed. the voltage went down to a range where i could adjust the resistor so i am now reading 118v between f1 and f2 when the spindle is off. Top...
  21. here is a link to my posting on craigslist in las...

    here is a link to my posting on craigslist in las vegas tool section

    Miller SYNCROWAVE 250 DX TIG welder - tools - by owner - sale
  22. 324139 The gen pulley measures 3-7/8" while the...

    324139
    The gen pulley measures 3-7/8" while the exciter pulley is 3-1/8"
    rpm on the generator is around 3000 while the exciter is running closer to 3500rpm
    Meter on f1 and f2 at spindle motor...
  23. Here are more pics Sorry about the orientation ...

    Here are more pics
    Sorry about the orientation

    324138

    324138
  24. Miller DYNASTY 350 DX Tig stick welder Tigrunner low hours! $6500

    I have a very clean Miller Dynasty 350 Dx Tig welder up for sale. The welder works great and looks clean. It has only 234 hours on the arc timer 60K cycles.
    IT is a 2007 model.
    Comes with: Miller...
  25. I'll post pic on monday. Im using a fluke to test

    I'll post pic on monday. Im using a fluke to test
Results 1 to 25 of 847
Page 1 of 34 1 2 3 4