Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Harri89

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    40
    Views
    3,660

    I have an hydraulic schematic in the manual, i...

    I have an hydraulic schematic in the manual, i just cant find the part where it branches to vertical head feed. There is a branch in the schematic for the vertical head counter balance piston and...
  2. Replies
    40
    Views
    3,660

    Got the feed motor back and running, still sounds...

    Got the feed motor back and running, still sounds loud to my ears, the shaking is away and and its quieter than it was.

    I noticed that if i push from the cooling fan the shaft moves axially...
  3. Replies
    40
    Views
    3,660

    I "welded" (melted) the motor cooling fan and let...

    I "welded" (melted) the motor cooling fan and let it cool and sit for night.270017

    I did a test fit with trued flange and to see the gear fit, it looks "good' to me.

    270018
  4. Replies
    40
    Views
    3,660

    Had some serious problems with chatter when...

    Had some serious problems with chatter when turning the mounting flange.


    First time machining something like this, the spots on outer edge was really hard
    I tries different speeds, feeds, added...
  5. Replies
    40
    Views
    3,660

    I removed the mounting flange from the motor and...

    I removed the mounting flange from the motor and took a closer look. I dont know what has happened to it because it has been repaired. Maybe someone dropped the motor to floor when removed and broke...
  6. Replies
    40
    Views
    3,660

    5 picture limit per post Inside the knee...

    5 picture limit per post

    Inside the knee
    269510
    269511269512
  7. Replies
    40
    Views
    3,660

    I have rear control on this machine and when i...

    I have rear control on this machine and when i was searching the cause of the noise, i managed to pull out the rapid traverse lever and screw the connecrion what engages front and rear levers.

    I...
  8. You need different TPI blades for different...

    You need different TPI blades for different thickness stock you are sawing. If its to fine, you burn it and it dulls prematurely. If its to coarse you loose teeth. With power feed you can run little...
  9. Replies
    40
    Views
    3,660

    The bevel gears had full contact to one...

    The bevel gears had full contact to one direction, i have it now back togheter and everything feels smooth so far. I need to repair the motor cooling fan and true up the motor mounting flange.

    I...
  10. Replies
    12
    Views
    652

    Its not that big job to get it done when needed....

    Its not that big job to get it done when needed. Drain oil from knee, Motor off, 4 bolts, Casing of the knee 9 bolts and the shaft with the bearings 4 bolts.
  11. Replies
    12
    Views
    652

    Cleaned all good and put it just back togheter...

    Cleaned all good and put it just back togheter and feels good for now! :)
  12. Replies
    12
    Views
    652

    I am 30 years old and i wish i wont sell this...

    I am 30 years old and i wish i wont sell this beauty never :)
    It was noisy when feed motor was running, i took it apart and didnt found any clear reason for the sound. Now i need to check the bevel...
  13. Replies
    12
    Views
    652

    Cincinnati vertical manual Milling machine feed...

    Cincinnati vertical manual Milling machine feed motor drive gear bearings, theres motor, idlers and then this with bevel gear in one end.
  14. Replies
    12
    Views
    652

    Taper roller bearing wear

    I am wondering if i should change these or not, they feel "ok"
    The contact area is matt, lost its shine.

    Can you help me by looking the pictures, thank you! :)

    269085269086269087
  15. Replies
    40
    Views
    3,660

    I used a dial indicator to sweep the motor flange...

    I used a dial indicator to sweep the motor flange contact area and its tilted 0.1mm, i assume this misalignment can make also some noise in the gears. The motor mount flange has been fixed by someone...
  16. Replies
    40
    Views
    3,660

    This machine has never been in a production use,...

    This machine has never been in a production use, so the gears ahouldnt be worn of too much of use.

    I can bring the bevel gear closer by grinding the shim.
  17. Replies
    40
    Views
    3,660

    YouTube (https://youtu.be/OaWsFX6vXZk) YouTube...

    YouTube
    YouTube


    Here are links to motor cooling fan and the feed motor drive gears. You can hear in the end of the video little noise which sounds little like bad bearing. It stopped when i...
  18. Replies
    40
    Views
    3,660

    268985268986268988268989268987 Here are some...

    268985268986268988268989268987

    Here are some pics from the tapered roller bearings. I think worth changing? I cant find any clear reason for the rattling sound when the motor was running. Also...
  19. Replies
    40
    Views
    3,660

    268981268982268983268984 Bearing races look...

    268981268982268983268984

    Bearing races look really gray and edges are shiny
  20. Replies
    40
    Views
    3,660

    More pics coming

    More pics coming
  21. Replies
    40
    Views
    3,660

    Any idea what causes the gear failure? The idler...

    Any idea what causes the gear failure? The idler gear(s) are the one what have broken on other machines?
  22. I have had this same problem with fp4a, filling...

    I have had this same problem with fp4a, filling to red line and after use it drains to front section of the horizontal spindle and then the oil level is over the red line. And seems to stay there....
  23. Replies
    40
    Views
    3,660

    Looks like tapered roller bearings, i hope rhe...

    Looks like tapered roller bearings, i hope rhe problem is with them and not deeper to keep job easier...

    Here is also picture of the motor. The shaft looks really long for a unsupported one??
    ...
  24. Replies
    40
    Views
    3,660

    When i Turn the gear by hand which is in the...

    When i Turn the gear by hand which is in the picture, what motor turns. There or somewhere is something wrong with bearing. It wont Turn smoothly and makes noise.

    Oil is already drained, it also...
  25. Replies
    40
    Views
    3,660

    So i removed the motor and motor bearings are ok....

    So i removed the motor and motor bearings are ok. The motor cooling fan has some wobble
    due the cast crack, which i assume makes some shaking to the machine, its minor but noticeable.

    For now...
Results 1 to 25 of 259
Page 1 of 11 1 2 3 4