Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: catch22

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    372

    How do I post a picture on here?

    How do I post a picture on here?
  2. Replies
    2
    Views
    372

    Allen Bradley 160-AA18NP03 Series C ?

    Hi everyone, I am pulling my hair out trying to figure out how to get the 160-aa18np03 series c to work on my lathe. The VFD is a 7.5 HP and my lathe motor is 3 HP, I have it wired up and have a...
  3. Replies
    7
    Views
    877

    So I took the top cover off and the oil is...

    So I took the top cover off and the oil is pumping fine, it was just hard to see it in that sight glass. Thanks for everyone's help.
  4. Replies
    7
    Views
    877

    Sag 12 Headstock Not Pumping Oil?

    Hi everyone, I finally got around to cleaning the Graziano Sag 12 transmission and changed the oil in it. I also drained the headstock oil and put fresh oil in it, got it wired up and it started...
  5. Replies
    5
    Views
    808

    Sorry I forgot to put in that it's for the...

    Sorry I forgot to put in that it's for the transmission oil pump, they pump around 70 psi I think.
  6. Replies
    5
    Views
    808

    Graziano Sag 12 oil pressure gauge?

    Just wondering if anyone can help me out, I have a car oil pressure gauge and was wondering if I could install it on my sag 12 on the transmission oil pump.
    And how it was piped into the oil lines....
  7. Thread: Waylube?

    by catch22
    Replies
    12
    Views
    1,525

    I just looked on there web site and it's $20...

    I just looked on there web site and it's $20 something a gallon, was that a special they you found?
  8. Thread: Waylube?

    by catch22
    Replies
    12
    Views
    1,525

    Waylube?

    Just wondering what everyone uses for waylube, can you just use a good motor oil?
  9. Replies
    2
    Views
    473

    Ok I got it figured out, one of the wires running...

    Ok I got it figured out, one of the wires running though the mill casting was broken, all fixed up and working.
  10. Replies
    2
    Views
    473

    Automatic Oiler voltage?

    I have an automatic Oiler on my machine and it says on the synchronous motor that it's 220 volts but it doesn't seem to be working when I hookup power to it, the wires seem pretty small to run 220...
  11. Replies
    24
    Views
    1,315

    Ok thanks guys, fast blow it is.

    Ok thanks guys, fast blow it is.
  12. Replies
    24
    Views
    1,315

    Fuses fast or slow blow?

    Ok my CNC milling machine, has 2 fuses between the main transformer and the rectifier I don't know if it has the right fuses or not, 250v 15 amp fast blow. Could I use slow blow fuses or is that a...
  13. Replies
    8
    Views
    846

    Thanks for getting back to me, yes thanks it is...

    Thanks for getting back to me, yes thanks it is FM50.
  14. Grease nipple do on the back of variable speed head?

    I'm just wondering what the grease nipple on the back of a variable speed head greases, I have put a few pumps into it while it's running and doesn't seem to make any sound changes. Just don't want...
  15. Replies
    8
    Views
    846

    3hp Teco FM50 on a 2hp motor?

    I just picked up a Teco FM50-203-c for a good deal, it's single phase in and 3 phase out. I'm going to use it on my milling machine that has a 2hp motor on it.
    My question is that there is nothing...
  16. Replies
    7
    Views
    1,104

    Oh ok, and can I delete the relays also, and use...

    Oh ok, and can I delete the relays also, and use the Mesa 7i77 board for the input signals, or will I still need the relays?
  17. Replies
    7
    Views
    1,104

    Using VFD to get 3 phase power

    Ok so I have an old 1987 CNC milling machine that I'm changing over to Linuxcnc.
    So I need 3 phase to run the spindle motor, what I'm wondering is when the main 240volt power comes into the machine...
  18. Replies
    16
    Views
    1,531

    Awesome, thanks for your help, I am going with...

    Awesome, thanks for your help, I am going with the WEG found one 2hp for $277 and a 3hp for $278, I'm thinking of going with the 3hp model even though I only need 2hp, just incase I upgrade the motor...
  19. Replies
    16
    Views
    1,531

    That's reasonable, what is the RF filter for?

    That's reasonable, what is the RF filter for?
  20. Replies
    16
    Views
    1,531

    VFD Recommendations?

    Hi everyone, I am having trouble finding a decent VFD for my milling machine. It is 2 HP 230volt 3 phase. What I am looking for is 1 phase in and 3 phase out. Also would like it to have built in...
  21. Replies
    0
    Views
    464

    FMX TD200 Series AC Drive

    I am looking at buying a VFD and was going to go with a Teco FM50 but they are discontinued. In there place the now sell the FMX TD200 Series AC Drive does anyone have any reviews on these, they...
  22. Replies
    3
    Views
    599

    It is a Delta vh-3600 and yes everything is...

    It is a Delta vh-3600 and yes everything is disengaged.
  23. Replies
    3
    Views
    599

    It's a delta cnc 3600 and yes z axis is...

    It's a delta cnc 3600 and yes z axis is disengaged.
  24. Replies
    3
    Views
    599

    Cnc knee mill, quill not moving.

    I have taken apart the z axis on my mill, the block that attaches to the quill was really loose. Now that it's all apart I can't move the quill up or down even with a small pry bar. Anyone have any...
  25. Replies
    0
    Views
    568

    Z axis connection to the quill question.

    I don't know if this is the right place to post this or not, if not let me know.
    I have a cnc knee mill and the z axis ball screw connection to the quill was really loose so I took it apart and the...
Results 1 to 25 of 177
Page 1 of 8 1 2 3 4