Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JS

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    33
    Views
    1,734

    Guessing that, Syncon R & O 480 or 560 oil...

    Guessing that, Syncon R & O 480 or 560 oil would work instead of grease. Just noticed they don't offer 560 anymore so 680..

    It sticks to everything and when used as a way oil. As an example: I...
  2. Replies
    33
    Views
    1,734

    1942 Marks engineers handbook ......less then 600...

    1942 Marks engineers handbook ......less then 600 FPM .001 per inch plus .001 for clearance.

    I've worked on 150 ton ball mills Bronze bearings 40" journals 19 RPM flood lube.... original clearance...
  3. Picture #4 shows your clutches up close. Look for...

    Picture #4 shows your clutches up close. Look for quick release tabs to push or set screw to loosen to rotate clutch adjustment nut.
  4. Thread: Mt. Taylor Machine

    by JS
    Replies
    2
    Views
    554

    Official Site of Lehmann Lathe...

    Official Site of Lehmann Lathe
  5. Replies
    21
    Views
    1,334

    You might be able to hand lap the spindle bearing...

    You might be able to hand lap the spindle bearing with the spindle using Time Saver lapping compound...

    otherwise your going to be scraping it.
  6. Why does this sound like a re-run of an idea from...

    Why does this sound like a re-run of an idea from several years ago?
  7. Replies
    51
    Views
    3,486

    used Clausing bed mill 1500lb - 2000lb table...

    used Clausing bed mill 1500lb - 2000lb table capacity..... 5 - 7.5 hp
  8. Enerpac does make a high volume 10k pressure unit...

    Enerpac does make a high volume 10k pressure unit , that uses a 120 or 220volt supply.

    Cost about $7k for (1) unit ......without any extras....

    Lower pressures are cheaper to repair...there is...
  9. Replies
    47
    Views
    2,864

    No, I wouldn't, worked next to a B&N main for...

    No, I wouldn't, worked next to a B&N main for years, cheaper to pay fines then slow down, then the local was going all the time.

    Machines were re-leveled 2-3 times a year.

    Current job at a...
  10. Replies
    87
    Views
    8,834

    Now repeat after me. .......Their problems, are...

    Now repeat after me. .......Their problems, are not my problems....

    Go on vacation or do something to get it off your mind. Then get back in the game.
  11. Replies
    10
    Views
    628

    Just an idea, Lathe with live tooling.... ...

    Just an idea,


    Lathe with live tooling....

    or

    fixture or fixtures that would clamp on center section of part. .......mitee bites on a fixture plate.....locate parts using two sides of a...
  12. She did the right thing. Would of been better if...

    She did the right thing. Would of been better if she gotten the other one as well.

    Actually the news, should of read ....AR-15 kills home intruder, owners are "OK".
  13. Replies
    67
    Views
    7,543

    Hopefully, you revisited the 2006 price to...

    Hopefully, you revisited the 2006 price to account for inflation....


    As to the problem at hand the middleman pays.

    Add a PITA charge for next PO....if there is one......
  14. Replies
    23
    Views
    2,751

    $5 to $10...........

    $5 to $10...........
  15. Depending on the age of the program and computer....

    Depending on the age of the program and computer. A computer savvy individual should be able to locate the information / access code in regedit.............or a similar file.

    If you don't know how...
  16. Thread: Baker key seater

    by JS
    Replies
    11
    Views
    2,034

    You should probably start a new thread with your...

    You should probably start a new thread with your machine pictured.

    Try these people [: Keyseat Cutters, Keyseat Cutter Tooling :]
  17. Turn the fit and install a custom adapter sleeve...

    Turn the fit and install a custom adapter sleeve for the bearings.

    And make sure the adapter sleeve has hydraulic assist for install and removal.
  18. Cool, I believe it has in the past, but It's...

    Cool, I believe it has in the past, but It's always neat to go back watch if you haven't in a while.
  19. Thread: G & L rebuild

    by JS
    Replies
    30
    Views
    4,077

    Well, if blakelyj2 is gonna bump the thread, I'm...

    Well, if blakelyj2 is gonna bump the thread, I'm going to ask...

    Did you ever get it back together? and What was your final solution for oiling the machine?
  20. Replies
    53
    Views
    3,892

    try one of these......

    try one of these...
    https://www.youtube.com/watch?v=0Bhn049IFNM
  21. Replies
    197
    Views
    21,378

    I'm gonna get the boss to get me one of those...

    I'm gonna get the boss to get me one of those Herman Miller Aeron chairs.

    The CNC job didn't have any chairs or stools, but with 6 min or less cycle times you didn't have time to really do...
  22. Replies
    68
    Views
    6,461

    I see someone else uses old iron. Good job...

    I see someone else uses old iron. Good job...
  23. Replies
    58
    Views
    4,001

    Before you mess with anything else. Pull the...

    Before you mess with anything else. Pull the gap out and clean remove burs. lightly stone mounting area etc....
  24. I knew that, I just want some left leaning...

    I knew that, I just want some left leaning psychopath, who wants to treat people like children to say it...

    You know the ones, people who think they know what is best for everyone else. The ones...
  25. I would almost imagine that a legal precept...

    I would almost imagine that a legal precept similar to the first sale doctrine would protect manufactures; of food ,goods, arms ,machines etc.

    Logically speaking unless it was a manufacturing ...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4