Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Fulcircleny

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Joe, I sent you a note

    Joe, I sent you a note
  2. Replies
    27
    Views
    1,489

    I run an Kaeser SM10 air center. I bought it used...

    I run an Kaeser SM10 air center. I bought it used with about 7k hours on it. The unit is in the same room as my CNC's, and I have an 80 gallon expansion tank at the other end of the building, next to...
  3. johfoster, This will be my long winded, serious...

    johfoster, This will be my long winded, serious reply. Please forgive me if in any way I offend you.

    My Dogs keep me sane, and I am at the age where being alone, is something I almost prefer,...
  4. Q:Would that still be true if they were...

    Q:Would that still be true if they were originally from Scotland, then became Danes?"

    A: ABSOPHUKINLUTLY
  5. I have 2 Great Danes that keep me entertained, I...

    I have 2 Great Danes that keep me entertained, I have had as many as 16 humans working for me, I much prefer the Danes...
  6. I used to have an older Sodick, I really was not...

    I used to have an older Sodick, I really was not competitive with it, started using New Jersey Precision, Bob Tarantino is the owner, 20 plus years later I still use them. Fast, reliable, fair...
  7. Just my two cents.. you will NEVER be sorry that...

    Just my two cents.. you will NEVER be sorry that you over protected any machine. Install the pins in the counter weight, "fix" the table to the spindle head if possible at the very least 'block' it....
  8. Replies
    29
    Views
    2,400

    Just call this company,Epoxy Technology Inc. We...

    Just call this company,Epoxy Technology Inc. We bonded thousands of 6061, disks together after being 'hard anodized'.
    The tech there will listen to your application requirements, and offer a few...
  9. Lock, I still have 1, 60 hp left if you are ...

    Lock,


    I still have 1, 60 hp left if you are interested, 1000.00 you pay shipping. worked when it came out of service 1 year ago.

    Chris
  10. Check your mail, I sent a pm Regards, Chris

    Check your mail, I sent a pm

    Regards,
    Chris
  11. Replies
    6
    Views
    1,538

    Bruce Preiser, in Brewster, MIGHT go into the...

    Bruce Preiser, in Brewster, MIGHT go into the city. Fourth generation rigger, has all the old and new toys to just about any job.

    Crane Rental - Based in White Plains, Carmel - Preiser Rigging &...
  12. We have done the tilt bed thing a number of...

    We have done the tilt bed thing a number of times. while it is flat, take it OFF the skid (before it even gets on the flatbed, if possible). re strap it down. If not already done, invert the head to...
  13. Replies
    3
    Views
    1,833

    If the seller will allow you , swap the BLD 50 (...

    If the seller will allow you , swap the BLD 50 ( or 30) or whatever in the X, with the Z, IF the issue migrates to the Z its the board. they can be rebuilt, in the 1200 dollar range. if That is the...
  14. Google the Anodic corp. Aluminum Hardcoat...

    Google the Anodic corp. Aluminum Hardcoat Anodizing | Anodic Incorporated They will send you a FREE wall chart about Hard coat and build up. Hang it on the wall and use it to refer to. It will be...
  15. Replies
    15
    Views
    1,586

    Thanks Doug, So far all except C/A design have...

    Thanks Doug, So far all except C/A design have said no, but I will keep on looking. Thank you everyone.
    Have a good day!
    Chris
  16. Replies
    15
    Views
    1,586

    will do, thank you!

    will do, thank you!
  17. Replies
    15
    Views
    1,586

    Thank you, Digger Doug, I will contact all in...

    Thank you, Digger Doug, I will contact all in this thread. Most vacuum brazers don't want anything to do with Aluminum, due to the low melting point. Several on the list have already said no, for the...
  18. Replies
    15
    Views
    1,586

    Found them Ox, thank you! Chris

    Found them Ox, thank you!
    Chris
  19. Replies
    15
    Views
    1,586

    Thank you Guys! I will look into all of these...

    Thank you Guys! I will look into all of these suggestions. Have a great day!
  20. Replies
    15
    Views
    1,586

    Thank you Bogart, and Norb I will look into both....

    Thank you Bogart, and Norb I will look into both.

    Have a good Tuesday!
    Chris
  21. Replies
    15
    Views
    1,586

    Vacuum Braze houses in the Northeast?

    Good afternoon all,

    As the title says, I am looking for recommendations for a Vacuum braze vendor in the Northeast. They must have the ability to re temper the material (6061-t6,) back to the T6...
  22. Replies
    14
    Views
    1,762

    as mentioned, remove the actual air spindle, then...

    as mentioned, remove the actual air spindle, then go around back, there is a counter weight, that is accesable from the rear, Moore actually has a little print, of a counterweight securing devise...
  23. Will, First, sorry about your FATHER. My...

    Will,

    First, sorry about your FATHER. My suggestion, is take as many pictures as possible, then upload them, or create a link to an album someplace, even on a Facebook page of it's own. We (the...
  24. Good morning all, I wanted to update this...

    Good morning all,
    I wanted to update this thread, One of the converters has been sold, Thank you Jim, best of luck with the converter, and your future endeavors.

    Second converter is still...
  25. Yes Mike, that is correct, with North America...

    Yes Mike, that is correct, with North America orientated to face forward..,


    Thanks Precision metal, I will look at it right now.


    Thank you guys..
Results 1 to 25 of 296
Page 1 of 12 1 2 3 4