Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Doug W

Page 1 of 32 1 2 3 4

Search: Search took 0.01 seconds.

  1. The OP has described an eccentric axial load. ...

    The OP has described an eccentric axial load. Not a lateral load like you have described.

    That eccentric axial load will create both compression and bending stresses.

    As mentioned up above,...
  2. Replies
    12
    Views
    1,055

    Watched the 1st 3 and it's fantastic to see pros...

    Watched the 1st 3 and it's fantastic to see pros rebuilding a 'real' lathe.
    Looking forward to more!
  3. Replies
    7
    Views
    455

    They are used to cut worm gears on a lathe and so...

    They are used to cut worm gears on a lathe and so correspond with gear nomenclature.

    Nobody ever seems to make worms and is why I have a 2 sets of virgin Mod and Dia change gears from 30 and 40...
  4. I sell on CL and have had good experiences doing...

    I sell on CL and have had good experiences doing so.

    If I am firm on the price I say so in the ad.
    If I haven't stated firm, I expect to be offered less.
    Either way I price it to sell with no...
  5. I don't think the point of contention is that...

    I don't think the point of contention is that buyers only want a fixed price and don't want to do any haggling.

    What I and I assume others don't want to do is have to 'ask for a quote' for a...
  6. Replies
    131
    Views
    24,830

    I just read through this whole thread and am glad...

    I just read through this whole thread and am glad to see that you have had good luck selling the parts off which keeps lots of other Schaublins up and running.

    Had you not bought this lathe it...
  7. Thread: Graziano sag 14

    by Doug W
    Replies
    27
    Views
    1,586

    It means the motor is not directly connected to...

    It means the motor is not directly connected to the spindle with just belts or gears but somewhere in there is a clutch pack that slips a bit when the spindle is engaged reducing the stresses like...
  8. Replies
    17
    Views
    2,872

    Opened up one feed box and disassembled the...

    Opened up one feed box and disassembled the other, I am shocked at how both feed box innards are it such excellent shape.

    Gears, shaft and forks have hardly any wear on 30 and 40 year old...
  9. Yep, seen it over and over. They go to their...

    Yep, seen it over and over.
    They go to their graves waiting to get their price on declining to valueless assets.
  10. Is that legal? How do you offer to sell...

    Is that legal?
    How do you offer to sell something you have no claim to?
  11. Because most used machinery dealers are stuck in...

    Because most used machinery dealers are stuck in the mid 50s, where they had all day to lite their pipe, do some phone chatting up customers while wearing their Ward Cleaver business attire.

    It...
  12. Well since he hasn't been on this forum in almost...

    Well since he hasn't been on this forum in almost 2 years I wouldn't expect an answer.
  13. Replies
    17
    Views
    2,872

    I tore into my motor with the bad leads, replaced...

    I tore into my motor with the bad leads, replaced them, new bearings, tested, painted and it is ready to be put back in service.
    Victory! Replacing Motor Leads

    One of the issues the dead parts...
  14. Replies
    17
    Views
    2,872

    Well, Toolmex told me about 1/2 of the missing...

    Well, Toolmex told me about 1/2 of the missing cross slide parts were unavailable and the parts they could get were pretty expensive.

    So I started hunting for a parts lathe.
    Found a dead 1980 Tug...
  15. Parting Out Andrychow Toolmex Polamco Tug-40 Lathe

    Well I had to find and buy a parts lathe to get the parts I needed to get my TUG40 lathe up and running.

    No accessories, like taper attachment or steady rest for sale.
    Really a complete lathe...
  16. Replies
    5
    Views
    784

    Very nice and just the right amount of talking in...

    Very nice and just the right amount of talking in the video!

    None of that jabbering away, repeating yourself for 20 minutes before doing anything.
  17. Replies
    17
    Views
    1,526

    About the same driving miles, and motor freight...

    About the same driving miles, and motor freight $$$ the whole way there and back.
    Verses much lower cost sea transport down the west coast.
  18. Replies
    12
    Views
    1,235

    You posted a lot of verbiage in this thread, when...

    You posted a lot of verbiage in this thread, when all you had to say is 'look at the other attached spec plate'. LOL
  19. Replies
    12
    Views
    1,235

    Here is the kicker! I removed the motor today...

    Here is the kicker!

    I removed the motor today and saw it has 2 spec plates on it, one with the 190/380 and the other with 208-230/460.
    They were on opposite sides and the latter obscured by the...
  20. Replies
    3
    Views
    515

    I think he wants to buy a Newell console. That...

    I think he wants to buy a Newell console.

    That "With" is maybe supposed to be WTB??
  21. Replies
    6
    Views
    958

    Still looking.

    Still looking.
  22. Replies
    12
    Views
    1,235

    Well that explains why I didn't see 380/190 volts...

    Well that explains why I didn't see 380/190 volts used anywhere.

    Thanks.

    Oh and the scrappies moved some iron so I saw the machine label the Parker power pack came off of and it is a Mazak.
  23. Replies
    1
    Views
    494

    Didn't have any known ozone resistant shrink...

    Didn't have any known ozone resistant shrink tubing so I coated the connections with insulating varnish after cleaning off the flux.
    The original connx were corroded.
    MG Chemicals 4228-225ML Red...
  24. Replies
    1
    Views
    494

    Victory! Replacing Motor Leads

    My Andrychow scrapyard rescue lathe motor leads were made of inferior insulation which crumbled away.

    Thought I would replace the leads. Found Forrest Addy's instructions and dove in.

    "Before...
  25. Replies
    14
    Views
    1,706

    And some carbide or HSS, and solder, flux and...

    And some carbide or HSS, and solder, flux and torch, and a way to sharpen it, and a way to hone it. :)

    Scraping on steel with a wood chisel, he may not have any of that.
Results 1 to 25 of 784
Page 1 of 32 1 2 3 4