Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Rob F.

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    13
    Views
    523

    Length of pins is easy to figure out, look at my...

    Length of pins is easy to figure out, look at my pics if needed, I did 2 pics, one with each pin all the way in, against its stop and you see where it goes to at the end. The one on the frame is...
  2. Replies
    11
    Views
    799

    How much does it all weigh?

    How much does it all weigh?
  3. You should just go get it.

    You should just go get it.
  4. Replies
    13
    Views
    523

    Mine can get gummed up with dust and crud and...

    Mine can get gummed up with dust and crud and ratchet not fall freely. I need to keep it clean and oiled so it works smoothly. Do you have both sliding pins as I showed in the pics I posted earlier...
  5. Replies
    13
    Views
    523

    Mine works with gravity, yours is probably same,...

    Mine works with gravity, yours is probably same, just slide the parts off, it is easy. Just pins and holes, super simple.
  6. Replies
    29
    Views
    16,906

    Flypresses are commonly used by blacksmiths. Hot...

    Flypresses are commonly used by blacksmiths. Hot or cold work.
    Screw press is not as popular unless you are making apple cider;)
  7. Replies
    27
    Views
    1,094

    Can you post a link?

    Can you post a link?
  8. Replies
    13
    Views
    523

    Yes Matt is right that you look to be missing a...

    Yes Matt is right that you look to be missing a pin, probably both pins. There are two pins that slide side to side to engage the handle, one is standard leverage and the other is high leverage....
  9. Replies
    13
    Views
    523

    Need to see pictures of what you have.

    Need to see pictures of what you have.
  10. Since you are selling and moving out soon, I...

    Since you are selling and moving out soon, I would just use caution tape around the spaces you need open the day before the spaces are needed.
  11. Replies
    14
    Views
    859

    If they dropped it off today I should be picking...

    If they dropped it off today I should be picking up at hub on Monday 4-6.
  12. Replies
    12
    Views
    687

    Yes, If you are careful and remove the shield....

    Yes, If you are careful and remove the shield. Probably held in by a tiny snap ring type of retainer.
    Seals are also removable to renew grease, use a very sharp pick to get behind the lip,...
  13. Replies
    14
    Views
    859

    YRC also has about the same fuel surcharge 21.9%...

    YRC also has about the same fuel surcharge 21.9% as of 3-25-20.
    U.S. Fuel Surcharge – U.S. Shipping Rates | YRC Freight

    Thank you guys for letting me know about YRC. :cheers: Here is an update...
  14. Replies
    14
    Views
    859

    YRC also charges a fuel surcharge Here are the...

    YRC also charges a fuel surcharge
    Here are the rates for YRC, not much different than fedex.
    U.S. Fuel Surcharge – U.S. Shipping Rates | YRC Freight

    An update after reading the good...
  15. I use propane with acetylene rosebud all the...

    I use propane with acetylene rosebud all the time. It works great, I even like it better than acetylene, it does not heat and burn the surface as fast. It is a little different to light but a tiny...
  16. Replies
    14
    Views
    859

    Yes, click second link in post 1 and scroll down,...

    Yes, click second link in post 1 and scroll down, look on the left side.
  17. Replies
    14
    Views
    859

    Anyone use fedex freightbox?

    Has anyone used this service from fedex? Seems like a great deal if I am to believe what I read on the website. linked below. It shows fedex has a flat rate box that is pallet sized with a 1200 lbs...
  18. Replies
    44
    Views
    2,316

    Adding video is just as easy, click the icon next...

    Adding video is just as easy, click the icon next to the picture, it is a couple frames of movie film.
  19. Replies
    44
    Views
    2,316

    Adding pics is easy. In the header above the text...

    Adding pics is easy. In the header above the text window there are some icons, click on the one that is a picture of a tree. This will let you add a picture from your computer, just have the pic on...
  20. Replies
    44
    Views
    2,316

    Sounds like he would be very happy knowing his...

    Sounds like he would be very happy knowing his lathe has a good home with someone who will appreciate it.

    A week or so ago I called on a CL add for a lathe. Turns out the realtor was trying to get...
  21. Replies
    5
    Views
    461

    A 3/8 HSS tool blank and arbor press?

    A 3/8 HSS tool blank and arbor press?
  22. In Colorado gun stores are considered an...

    In Colorado gun stores are considered an essential business.
    Not here in Calif though.
  23. Replies
    12
    Views
    629

    So the air is being trapped under the piston? Is...

    So the air is being trapped under the piston? Is there room for you to drill a small hole through the piston and put a check ball in there? 1/16" or smaller hole, or at least an orifice in a bigger,...
  24. Replies
    12
    Views
    629

    Can you just drill the high point for an air...

    Can you just drill the high point for an air bleeder? Buy them or just make one with a cone point set screw.
  25. maybe we get elon to do it? Would a tesla rocket...

    maybe we get elon to do it? Would a tesla rocket on autopilot run into anything on the way up?:D
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4