Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: pcasanova

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    1,283

    can you T1 M30 T2 M30 and change...

    can you

    T1
    M30

    T2
    M30

    and change tools? M30 might not be needed but on one machine it
    tried to rerun or something that the other machine didn't do without
  2. if there's threads or someway to get a stop at...

    if there's threads or someway to get a stop at the end of the shaft and use a hollow jack to pull it out.
  3. Replies
    15
    Views
    1,283

    Hey Mark, I know the 2-3-2 thing has to be...

    Hey Mark,

    I know the 2-3-2 thing has to be done quickly on step 9. when you switch you have
    to wait for a led, switch wait 1 second (no longer than 3 seconds) or it won't go.
  4. Replies
    8
    Views
    441

    yes, I also made about 5 more and turn down the...

    yes, I also made about 5 more and turn down the backside to match the collet/material size I have to use.

    hopefully I'll have a new video in a few months of something similar but I'm going to have...
  5. Replies
    8
    Views
    441

    this is what I did for a center and keeps your...

    this is what I did for a center and keeps your sub open for takeover

    YouTube

    Like orange said I just synched the spindles a did a % of torque press.
  6. Replies
    15
    Views
    1,283

    trying hitting the w (has 2 arrows facing down on...

    trying hitting the w (has 2 arrows facing down on it) and see if something changes on the screen from channel 1 to 2. If it does I think that may lead to your problem.

    From what I found was...
  7. here's the outcome of that, on a lathe but you...

    here's the outcome of that, on a lathe but you get the picture

    265660265661265662
  8. Replies
    26
    Views
    2,062

    Poll: We bought about 10 new Haas's about 3 years ago...

    We bought about 10 new Haas's about 3 years ago and had rust issues. The tech said it's your coolant concentration (pink cimcool), the older Haas we have didn't show the problems or any other...
  9. Replies
    15
    Views
    1,283

    side note after you do get everything reloaded...

    side note after you do get everything reloaded there may be "h? m99" commands you run in mda to turn on features. When I've had to reload in the plc (lathe) I have to go in and turn on the chucks,...
  10. Replies
    15
    Views
    1,283

    There's 2 versions of the control, harddrive on...

    There's 2 versions of the control, harddrive on the high end model on a pccard on the other. but here's the procedure
    the files should be stored on the hd or pccard, there may be multiple, if there...
  11. you could always pull it out as far as needed...

    you could always pull it out as far as needed then after the parts done bring the sub back
    over and use it to chuck up and push the bar back into the main.
  12. If you do a ductless the only thing going through...

    If you do a ductless the only thing going through the wall is the copper and drain. about 1 ton per 500 sq. is a rough guesstimator. I did a 1 ton unit for my garage and it blows cold air but not...
  13. Replies
    26
    Views
    1,642

    check your voltage at the pump?

    check your voltage at the pump?
  14. Replies
    21
    Views
    2,326

    might be too late but had something similar when...

    might be too late but had something similar when a cooling channel got plugged on a integral motor machine and had to pull the stator. All thread was mentioned, but I used hollow hydraulic jack to...
  15. if not that route you can go something like this ...

    if not that route you can go something like this

    262018

    I'm thinking something like this is what camerman was thinking, but instead of vacuum on one side of the piston, air on the
    other side...
  16. no vacuum block is what I meant. I thinking of a...

    no vacuum block is what I meant. I thinking of a block 2'x3-4wide and about 1.5-2 thick, chamfer the front edge to miss that rad. mill a pocket 1.25 x 22 back enought to miss the hole feature or...
  17. maybe some sort of vacuum fixture

    maybe some sort of vacuum fixture
  18. teachme is on it with the a movement, but...

    teachme is on it with the a movement, but machine in air first to make sure the angle goes the way you want. 0 on the compass may not be where you would assume.
  19. siemens uses cycle83 instead of the g83. the...

    siemens uses cycle83 instead of the g83. the conversation side should walk you through the cycle.
    Thats the part of the program you will have to modify. And to use it in a fanuc style g-code you...
  20. If all he did was delete the files and not any...

    If all he did was delete the files and not any sort of wipe you may be able to get the programs back.
    find an undelete program you can run from a pen/usb drive (minimize the chance of over writing...
  21. do this often to trace logo's ect for signs. and...

    do this often to trace logo's ect for signs. and until
    the end of the year you can get draftsight for free.
    and do the exact same thing, basically an autocad clone.
  22. Replies
    29
    Views
    3,000

    positive/polished insert? I like the Iscar AS...

    positive/polished insert? I like the Iscar AS series. Also works really good on plastics, very sharp.
  23. Replies
    24
    Views
    2,843

    259113 from the 840d programming manual

    259113

    from the 840d programming manual
  24. Replies
    42
    Views
    2,913

    seems you have the right tool in. I did find...

    seems you have the right tool in. I did find this don' know if have/seen this,

    http://www.productivity.com/wp-content/uploads/2015/04/PIC-HyundaiWia_SKT100-200-CNC-Installation-Maintenance.pdf
    ...
  25. Replies
    7
    Views
    667

    on mine, servo2 you jog back and go into 4- misc...

    on mine, servo2 you jog back and go into 4- misc functions, request ref. carriage rolls back til it hits the physical stop ask to power off for 2 seconds. power back on and good to go.
Results 1 to 25 of 396
Page 1 of 16 1 2 3 4