Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Man, how I'd like to have one of those in the...

    Man, how I'd like to have one of those in the 54"c/c config.
  2. Replies
    15
    Views
    722

    One of those Flir clip on thermal imagers for...

    One of those Flir clip on thermal imagers for your phone will pay for itself in a heartbeat between compressed air leaks and air leaking from outside into the shop or vice versa.

    Sent from my...
  3. Replies
    7
    Views
    290

    I'm interested in hearing this as well. You...

    I'm interested in hearing this as well.

    You trying to avoid the roof?
  4. Definitely a dikfer. Sent from my SM-G973U...

    Definitely a dikfer.

    Sent from my SM-G973U using Tapatalk
  5. But Monarch says the opposite, that after...

    But Monarch says the opposite, that after leveling the machine should be lagged to the floor.

    Anyone have an ATW manual? It'd break the tie. :)

    Sent from my SM-G973U using Tapatalk
  6. Replies
    22
    Views
    1,086

    Ya, I do believe those are incorrect. ...

    Ya, I do believe those are incorrect.

    Depending on your situation, may be just as easy to redrill them proper instead of returning.

    Sent from my SM-G973U using Tapatalk
  7. Replies
    23
    Views
    1,173

    Seriously? I get more miles out of brake pads...

    Seriously? I get more miles out of brake pads than that.
  8. Yes, I read post #10 and it was helpful. Your...

    Yes, I read post #10 and it was helpful.

    Your comment struck me as odd, that's all.
  9. Replies
    11
    Views
    538

    Still boils down to how small you wanna go. You...

    Still boils down to how small you wanna go. You boring pilot holes for #0-80 screws or rechambering a Mk45 deck gun?
  10. Replies
    23
    Views
    1,173

    Neat pic. At the bottom of that engine, have...

    Neat pic. At the bottom of that engine, have they routed a coolant line through the oil filter mount? Presumably as a heat exchange method?
  11. It's a touch odd that the moderator of the...

    It's a touch odd that the moderator of the metrology forum is recommending a $10 hardware store unit to replace the OP's desired Starrett unit, no?
  12. Replies
    11
    Views
    538

    Minimum bore diameter will be your guiding...

    Minimum bore diameter will be your guiding factor, so how small you wanna go?

    I've had good luck with Maritool's solid carbide insert-type bars. They start at 1/4" OD with .31" min ID. SOLID...
  13. Replies
    52
    Views
    4,190

    FWIW- I learned yesterday that 10% concentration...

    FWIW- I learned yesterday that 10% concentration 690XT doesn't burn your eyes very bad. :toetap:
  14. Scribe the line with the boring head, plunge cut...

    Scribe the line with the boring head, plunge cut the bulk of the material with an endmill, then fnish with the boring head. Using the bolt circle function of your DRO (or some math) should lead you...
  15. Replies
    4
    Views
    415

    Pulse TIG principles

    Hello all,
    I'm looking for basic guidelines on how to setup my TIG (Invertec V160T) for pulse.

    How does one select a frequency, what effect does 20hz have on the puddle vs 200hz?

    What amount...
  16. Replies
    32
    Views
    1,772

    An axiom for life. ^^^

    An axiom for life. ^^^
  17. Replies
    32
    Views
    1,772

    Why no love for the Lincoln Invertec line? ...

    Why no love for the Lincoln Invertec line?

    Dual input voltage, pulse, hi-freq/lift/stick settings, 100% duty cycle to ~80% output, quick connect leads...

    I love mine but no one really talks...
  18. Replies
    19
    Views
    1,064

    My dad's old VSR drill had what amounted a...

    My dad's old VSR drill had what amounted a throttle limiter on the trigger so no matter how hard you gripped it the drill would only spin so fast. I've not seen those on newer drills but itd sure be...
  19. I'd turn a tapered shaft, then ID thread the...

    I'd turn a tapered shaft, then ID thread the small end 1/2-13. Turn your ring's ID with a matching taper and sufficient OD for strength. Ring needs a nice bevel so as not to pinch the wire, and the...
  20. Replies
    6
    Views
    648

    I'd like 2 of each 3/4" cutters. Paypal work? ...

    I'd like 2 of each 3/4" cutters. Paypal work?

    Sent from my SM-G973U using Tapatalk
  21. Replies
    6
    Views
    648

    These are carbide or HSS? Sent from my...

    These are carbide or HSS?

    Sent from my SM-G973U using Tapatalk
  22. Makes sense. I could probably rig up something...

    Makes sense. I could probably rig up something like a driveshaft from the lathe chuck to a jack shaft and use that to turn the center.

    Sent from my SM-G973U using Tapatalk
  23. How is this done? I'm picturing a tool post...

    How is this done? I'm picturing a tool post grinder on the compound and using the cross slide for infeed. Then just let the center float against the grinding wheel until it sparks outs?
    ...
  24. 6. And DROPROS handled mine under warranty a...

    6. And DROPROS handled mine under warranty a while back at 7 years.

    Sent from my SM-G973U using Tapatalk
  25. Replies
    4
    Views
    348

    Something like a Velocite? Sent from my...

    Something like a Velocite?

    Sent from my SM-G973U using Tapatalk
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4