Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mtndew

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    463
    Views
    27,446

    We paid $6,200 for the 16k Dual Contact spindle...

    We paid $6,200 for the 16k Dual Contact spindle replacement.
    For reference, a spindle on our Okuma genos M560V is pushing $30k.
  2. Replies
    463
    Views
    27,446

    They tried to talk us out of the dual contact...

    They tried to talk us out of the dual contact also. Once you go dual contact, you never go back. :cheers:
  3. Thread: Big-plus

    by Mtndew
    Replies
    16
    Views
    923

    I believe you can't run Big Plus in a non-Big...

    I believe you can't run Big Plus in a non-Big Plus spindle.
    BUT
    you CAN run a regular Cat holder in a Big Plus.

    To the OP: They are worth it, and not really that much more than a regular cat 40...
  4. Replies
    463
    Views
    27,446

    It's definitely pushing the limits for sure....

    It's definitely pushing the limits for sure. Stubby holder, dual contact, etc..
    We've slowly crept up to those parameters and found a sweet spot.
    Do I recommend this cut for others? lol no....
  5. Exactly, I wouldn't have a free hand to hold my...

    Exactly, I wouldn't have a free hand to hold my beer because I'd be flipping switches constantly.
  6. Replies
    12
    Views
    575

    Go to your local pet supply store and buy a $30...

    Go to your local pet supply store and buy a $30 aerator, drop it into your tank. This will solve most odor problems.
  7. Replies
    13
    Views
    1,010

    I was referring to the "start" notes. Meaning the...

    I was referring to the "start" notes. Meaning the datum is shifted and not the edges of the part.
    Another place I've seen them a lot is on linear gear racks where the "start" is on a certain tooth...
  8. Replies
    463
    Views
    27,446

    We had to replace our spindle on our Brother just...

    We had to replace our spindle on our Brother just last week. Operator forgot to turn the coolant on cutting 6061 aluminum.Had the same grinding noise the OP did, then the stud busted off and after...
  9. Thread: Chick One LOC?

    by Mtndew
    Replies
    6
    Views
    454

    ^^ +1 Call your Chick distributor and have them...

    ^^ +1
    Call your Chick distributor and have them bring the Chick rep for a demo.
    I don't have the new style,but we have a dozen of the older style. They are worth every penny.
    Solid middle = no...
  10. Replies
    10
    Views
    600

    I agree with the above, your control is unable to...

    I agree with the above, your control is unable to process lines of code quickly. Your best bet is to just feed it slower and/or make your moves longer.
  11. Replies
    17
    Views
    912

    It depends really. Are these 1st op parts where...

    It depends really.
    Are these 1st op parts where you're qualifying the outside to make sure the holes will be in location?
    Or are they 2nd op parts where a finished edge is up against a stop?
    If...
  12. Replies
    25
    Views
    1,436

    I've never heard of Wera, did you mean Wiha?

    I've never heard of Wera, did you mean Wiha?
  13. Replies
    13
    Views
    1,010

    Not necessarily. You'll often see callouts like...

    Not necessarily. You'll often see callouts like this on weldments too.
  14. Replies
    13
    Views
    1,010

    The center line of that dowel hole is your X0Y0...

    The center line of that dowel hole is your X0Y0 Datum, and that hole is 15mm from the dowel, not the end of the part.
  15. I've never heard of Feeler machines, have they...

    I've never heard of Feeler machines, have they been around a while? Maybe popular across the pond?
    $70k seems very entry level for a 5ax.
  16. Replies
    30
    Views
    1,700

    You wear panties? :D

    You wear panties? :D
  17. Replies
    32
    Views
    1,167

    I don't see how anyone could say that Verniers...

    I don't see how anyone could say that Verniers are easier to read.
    More accurate? Possibly,but easier no.
  18. Replies
    124
    Views
    5,384

    Same here. I can't recall the last time I got the...

    Same here. I can't recall the last time I got the flu but it was when I was a young teenager (now 50).
  19. Replies
    25
    Views
    1,969

    Just know that Metric uses both 90 and 82, but it...

    Just know that Metric uses both 90 and 82, but it depends on the size of the screw.
    If I remember correctly, larger than 20MM use an 82 deg.
  20. Is this what you were thinking of? YouTube...

    Is this what you were thinking of?
    YouTube
  21. Another vote for Edge Precision. I really enjoy...

    Another vote for Edge Precision. I really enjoy his videos.
    Not sure if his channel qualifies as an influencer though,but his a lot of stuff he does is really interesting on that Mazak. Definitely...
  22. Thread: ISCAR drill

    by Mtndew
    Replies
    8
    Views
    529

    What does Iscar recommend?

    What does Iscar recommend?
  23. Replies
    30
    Views
    1,828

    mill,flip repeat. Flood the hell out of...

    mill,flip repeat.

    Flood the hell out of it,don't let the tool rub or get hot.
    And use SHARP TOOLING!
  24. Replies
    8
    Views
    531

    My google didn't return much either. Is the lock...

    My google didn't return much either. Is the lock a standard lock like something you can buy from McMaster-Carr?
  25. Replies
    11
    Views
    885

    My first thought ran to Crown Boring in...

    My first thought ran to Crown Boring in Detroit,but they have boring mills.
    Did a Google search for large Part Turning and this was the top result:
    Large Part Turning provided by Circle Boring &...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4