Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    3
    Views
    200

    All written down - helps you KNOW with a little...

    All written down - helps you KNOW with a little measuring of what is there

    Standard Tapers

    Have Fun
  2. Thread: Hendey 14x6

    by johnoder
    Replies
    67
    Views
    3,853

    Pat's parts are instructive - the shaft for the...

    Pat's parts are instructive - the shaft for the rear bevel is HEADED - meaning it has to come out from the gear side - not the head stock side

    315806
  3. Use it - fix it if needed. Do note the...

    Use it - fix it if needed.

    Do note the brazed carbide tooling has mostly been on display - you'll need the typical Baldor double end diamond wheel grinder to have your way with such tooling - I...
  4. Replies
    4
    Views
    313

    Firstly - is motor running right direction? ...

    Firstly - is motor running right direction?

    Remove side plate to see that ram is going SLOWER on the cutting stroke and FASTER on the return stroke (the crank pin on the bull gear will be in...
  5. Replies
    10
    Views
    736

    Here is recent availability - see Post #9 New...

    Here is recent availability - see Post #9

    New to me P&W 1694 12x54
  6. Replies
    2
    Views
    296

    Not for Cinc, but had to make the clutch. This...

    Not for Cinc, but had to make the clutch. This was just a modified off the shelf forged machine crank

    315601315602315603315604315605
  7. Replies
    8
    Views
    676

    Have 2KM / 3 KM manual that can be emailed if you...

    Have 2KM / 3 KM manual that can be emailed if you care to private message me that email address. The KM was a few years prior to yours
  8. Old "M" Monarch - gives an idea how many pieces...

    Old "M" Monarch - gives an idea how many pieces the shaft assy consists of

    315541

    In your minds eye you can imagine the PILE of special tools Monarch had to invent for this job
  9. Maybe 1200 max - all done with motor sheave and...

    Maybe 1200 max - all done with motor sheave and appropriate length belts. In other words, you could probably have a 1942 CK with less than 500 top end. Depended entirely on what the original...
  10. Replies
    5
    Views
    587

    As near as I know all such clutches are "right -...

    As near as I know all such clutches are "right - tight" and "left- loose"
  11. Replies
    10
    Views
    736

    Be selective Oldies are "slope heads' - unlike...

    Be selective

    Oldies are "slope heads' - unlike the "square" one the dealer did not have - photo in this thread

    These later ones have the hard ways - and often go faster speed wise

    They were...
  12. Replies
    5
    Views
    587

    Probably have to rig up a tool to bump it loose -...

    Probably have to rig up a tool to bump it loose - pair of hard wood jaws to fit knob and on out from there so you can un-stick it

    almost never stuck ENGAGED
  13. "Dual Drive" combines both geared speeds and belt...

    "Dual Drive" combines both geared speeds and belt speeds - may go there

    The 14" Monarch may go there - its likely to be the 12" that swings 14 1/2"

    Maybe you should ASK seller?

    Lots of info...
  14. Replies
    7
    Views
    1,370

    Gives an idea of age - image scanned from approx...

    Gives an idea of age - image scanned from approx 1910 catalog of the 18" Standard

    315433315434
  15. Its a 13 Heavy Duty RP and the "air thing" used...

    Its a 13 Heavy Duty RP and the "air thing" used to operate a collet system I suppose. The collet closer is the piece LARGER than the spindle nose threads

    The 626 says it is from 1942

    What ever...
  16. Replies
    6
    Views
    572

    CMM (the milling machine folks) liked 5/32 per...

    CMM (the milling machine folks) liked 5/32 per foot on their taper gibs
  17. Taft Peirce #1. The very best in my opinion and...

    Taft Peirce #1. The very best in my opinion and I have had mine for about 25 years. They are 5 X 12

    Made in Woonsocket, Rhode Island

    On page 86 in second pub

    Taft-Peirce Mfg. Co. -...
  18. A guess might be weld bevel maker for good size...

    A guess might be weld bevel maker for good size pipe
  19. Replies
    2
    Views
    415

    I'd guess really old (NMT50 goes back to circa...

    I'd guess really old (NMT50 goes back to circa 1928) but never used

    Why?

    Straight cut teeth - almost unheard of only a bit later - and helical instead
  20. To me, its the stuff that can be removed easily -...

    To me, its the stuff that can be removed easily - like on this cast iron. If this lathe bed was steel, it would be a much more issue

    315073315074
  21. Replies
    41
    Views
    10,780

    Don't neglect to turn it the right way...UNDO is...

    Don't neglect to turn it the right way...UNDO is up and away from you :D
  22. Assuming you refer to common vee belts......LOOK...

    Assuming you refer to common vee belts......LOOK on belt for a number - like B90 (or BX90). Purchase belts with the same number
  23. Replies
    10
    Views
    509

    Any honing shops in that part of the world? ...

    Any honing shops in that part of the world? Texas Honing in North Houston does 20 footers every day, but the shipping won't be cheap
  24. Replies
    1
    Views
    206

    You could look on VM for the latest dial type...

    You could look on VM for the latest dial type number 2 weight and use that as an educated guess since the DTs where the heaviest
  25. Thread: 30tpi, SB 9A

    by johnoder
    Replies
    3
    Views
    279

    Or.....42/56 = .75 and 40 times .75 = 30

    Or.....42/56 = .75 and 40 times .75 = 30
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4