Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Stang Bladeworks

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Here it is almost completly together. 264363

    Here it is almost completly together.
    264363
  2. Today I was able to grind the chuck and make a...

    Today I was able to grind the chuck and make a sample part. the finish isn't the best on the chuck. I did run coolant but there are some burn marks. I also managed to dig the wheel in a couple times....
  3. I definitely feel it was worth the money. In...

    I definitely feel it was worth the money. In order to remove some of the parts related to the automation function I had to destroy them. (cut them) some parts were previously damaged so I wasn't...
  4. Thanks for the reply, Again I am out of town...

    Thanks for the reply,

    Again I am out of town working but I can post more pics this weekend. From what I can tell the spring is not the issue. The screw seems to pull it down too far. With no screw...
  5. I have considered this as a possibility. I'm not...

    I have considered this as a possibility. I'm not sure if this type of thing is common for the era. If drilled out the oil would serve to lubricate the shaft. None of the items from this oiler seem to...
  6. That's exactly what i'm saying. I was unaware of...

    That's exactly what i'm saying. I was unaware of this type of bushing. That seems to make sense but when I pulled the shaft out after it had been sitting for a week it was bone dry. It didn't seem...
  7. I also further investigated the oil routing from...

    I also further investigated the oil routing from the one shot. There are no holes in the bushing where the shaft goes so it doesnt seem like the oil goes anywhere. It seems to have no purpose. Any...
  8. Here are some more pics. I attempted to install...

    Here are some more pics.
    I attempted to install the table but i realized that the screws that hold the lubrication rollers are too short on the flat way. They do not allow the roller to extend above...
  9. I did not get any metering units. Right now all 4...

    I did not get any metering units. Right now all 4 channels get lubrication. It may not be perfectly distributed but they are getting oil. I'm just slightly confused about the two channels that feed...
  10. Im just working out of town now but when i get...

    Im just working out of town now but when i get back ill take some better pictures of the ways.
  11. I installed the oiler and i have some questions....

    I installed the oiler and i have some questions. 2 of the hoses terminate into holes in the housing for different spindles that do not seem to reach the actual spindle. It seems to only reach the...
  12. Here are some pics of the ways i got rescraped....

    Here are some pics of the ways i got rescraped.
    263434
    263435
    263436
  13. I picked up my parts from the machine repair...

    I picked up my parts from the machine repair shop. Ill post some pics later. I reassembled the column and spindle. I removed all the grease and dirt then coated the ways with way oil prior to...
  14. I did eventually get all the paint and goop off....

    I did eventually get all the paint and goop off. Richard i followed your advice regarding tractor paint. The only paint I could source was john deere branded. I tried brush on and spray cans. The...
  15. Thanks for all the replies everyone. I will post...

    Thanks for all the replies everyone. I will post up my progress later this weekend. For now this is where I stand. My grinding room looks pretty bad right now. Im pretty sure I have simulated...
  16. Thanks, I will check these out.

    Thanks, I will check these out.
  17. Thanks, I appreciate that. The wheel size is...

    Thanks, I appreciate that. The wheel size is 7x(1/2)x(1-1/4). I cant measure the exact tolerance right now because every single part is dismantled. It didn't look like you could fit a larger wheel on...
  18. Good point, I have been wearing a respirator this...

    Good point, I have been wearing a respirator this whole time, I think I would be dead already otherwise. This paint dust is very fine and I cant imagine its too good for you.
  19. Thanks, I will look into it. I spent about 6...

    Thanks, I will look into it. I spent about 6 straight hours today with an angle grinder so I think I'm almost done. That way sounds much easier than what I have been doing. I have also been learning...
  20. Thanks, so far I have used a wire wheel to expose...

    Thanks, so far I have used a wire wheel to expose the black goop then used a gator rust remover disk to get rid of most of the goop. I have them been getting into tight areas with a chisel. It is...
  21. unfortunately moving it is not easy. it took...

    unfortunately moving it is not easy. it took quite a bit of effort just to get in place. I wish I could do this but it just wont work for me. I would need to get a few people just to get it on a...
  22. So far the painting process has been aweful. I...

    So far the painting process has been aweful. I have found some john deere paint that seems to work. None of the department store paint worked at all. It stayed tacky for days. My real problem is with...
  23. Thank you. As soon as I source some wheels ill...

    Thank you. As soon as I source some wheels ill let everyone know what I found. I really appreciate all the help and tips. I will grind the chuck but ill get some practice in first.
  24. Thanks. Good idea about the spotter and it will...

    Thanks.
    Good idea about the spotter and it will give me some practice with the machine. I dropped the parts off today. Hopefully ill have it together soon.
  25. Thanks for the replies everyone. I plan to drop...

    Thanks for the replies everyone. I plan to drop off my parts to be scraped tomorrow. I think ill stick to basic grinding techniques for now. Good points about using shims for imperfect stock. I...
Results 1 to 25 of 54
Page 1 of 3 1 2 3