Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Milland

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    7
    Views
    921

    Holy Carp, I've never had to get permits for...

    Holy Carp, I've never had to get permits for racking. I guess WA is much more seismically active, out here in NH we take our relatively stable geologicals for granite...
  2. Sticky: If you want to hitch your wagon to DJT, Rudy...

    If you want to hitch your wagon to DJT, Rudy Ghouliani, and the rest of that cohort don't come crying to me when it goes off a cliff.
  3. Sticky: I am sorry that you're so reduced in capacity...

    I am sorry that you're so reduced in capacity that you think the above is:

    A) "True" (true in quotes because it's more accurate to call it delusional fantasy).

    B) Seem to love the Orange...
  4. Sticky: I hope not, he and I have had some disagreements...

    I hope not, he and I have had some disagreements on a few things. And since he's out in CO (I think), it would mean one of us got teleported...

    But since you asked (well, not really) - how did...
  5. Replies
    10
    Views
    551

    Welcome to the Jungle! Don't worry about the...

    Welcome to the Jungle! Don't worry about the shitposts, it's just a little ritual they have here. What's happened is that you posted a question with little information, that's blood in the water for...
  6. Replies
    2
    Views
    226

    Check out the Llambrich line of chucks too,...

    Check out the Llambrich line of chucks too, quality on par with Albrecht, and less expensive. Doesn't have the name recognition that Albrecht has in the US, but available with a little searching.
    ...
  7. Replies
    131
    Views
    9,458

    I like to watch... :leaving:

    I like to watch... :leaving:
  8. Replies
    26
    Views
    1,101

    Starts with a properly ground, high quality saw,...

    Starts with a properly ground, high quality saw, and I do prefer carbide if it's a rational size (after 3"OD it gets expensive).

    Then, I sometimes will make my own arbors with as large a clamping...
  9. Replies
    5
    Views
    404

    Look at full-form threadmills, which can cut...

    Look at full-form threadmills, which can cut reasonable depths of thread in one pass (although you might be well served to use two or more passes with Inconel to preserve tool life).

    If you need a...
  10. Replies
    14
    Views
    1,169

    In fairness, most "turning" inserts have various...

    In fairness, most "turning" inserts have various tip radii options, and unless you're cutting UNJ-style threads you really should be using proper threading inserts anyway, which have a more strict...
  11. Replies
    62
    Views
    3,426

    Maybe Jet offers replacement threads?

    Maybe Jet offers replacement threads?
  12. Replies
    62
    Views
    3,426

    That "5% of newbs want to fight" I pulled out my...

    That "5% of newbs want to fight" I pulled out my ass should have included a "1% only joined to fight". He's already in my blocked file.
  13. Hey Sidebite, We have a number of...

    Hey Sidebite,
    We have a number of people here involved with the racing industry, if you ever feel inclined to start a thread about your experiences in it I'm sure a lot of folks would be...
  14. Got any pictures of the bearings? Was the...

    Got any pictures of the bearings? Was the failure diagnosed as noise, excess play, degraded finish or ?

    No coolant, but any other debris? If you had multiple failures it should be relatively...
  15. Sticky: Given Trump's MO, it's certain that the decision...

    Given Trump's MO, it's certain that the decision to leave was made on what benefit accrued to DJT. Everything's a transaction, and all transactions are to the glory of DJT.

    That's a lot of very...
  16. Cam timing. Doesn't have to be, but because OHC...

    Cam timing. Doesn't have to be, but because OHC engine can run to higher RPM, the cam timing is designed to get the higher top-end power, at the cost of less low-end grunt. Intake and exhaust paths...
  17. Replies
    7
    Views
    760

    With a side of unknown pathogens for good...

    With a side of unknown pathogens for good measure. ;)

    I've seen vids of the aftermath of centrifuge crashes - it's not pretty. Scale it up to a commercial jet engine and there'd be nothing left...
  18. Replies
    10
    Views
    506

    Random things you can try (after shutting down...

    Random things you can try (after shutting down power):

    Carefully remove and reseat circuit boards and cable connectors to make sure electrical contacts aren't compromised. Can use contact cleaner...
  19. Replies
    7
    Views
    529

    I'm having flashbacks to that guy who wanted to...

    I'm having flashbacks to that guy who wanted to set up screw machines to make his own "high quality, high strength" onesie-twosie bolts...
  20. Replies
    5,685
    Views
    163,593

    I haven't been keeping up (sorry), is this the...

    I haven't been keeping up (sorry), is this the "one nation" thing you're speaking of?

    One-nation conservatism - Wikipedia

    If so, it doesn't sound bad to me. Is there another conspiracy I need...
  21. Replies
    62
    Views
    3,426

    You've now made five posts to this thread trying...

    You've now made five posts to this thread trying to "White Knight" for the OP without offering your own solution to his problems. Good work...

    To the OP - this is a forum for professional...
  22. You also have to consider harmonics and max tooth...

    You also have to consider harmonics and max tooth loads, not to mention adding a sh!t ton of complexity to a system that already works.

    Why do you want to do this? And, uh, your name is...
  23. Sticky: First paragraph references a Democracy, hence...

    First paragraph references a Democracy, hence your responsibility. Next one says "I made no commitment to the Kurds".

    But you did. As a member of THIS DEMOCRACY you are responsible for legally...
  24. Sticky: It's not even that in a fit of pique Trump...

    It's not even that in a fit of pique Trump abandoned the Kurds - it's what motivated the sellout. Is it purely a matter of [ahem?] the Kurds didn't support the Normandy landings in WWII [more...
  25. Sticky: Dear Sir. It has come to our attention that you...

    Dear Sir. It has come to our attention that you conflate "dealing with reality and facts which are self-consistent" with being unoriginal. Such difficulty in handling veritus indicates a slavish...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4