Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: seagiant

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    785

    Hi, Here is my Retro 1911 build I did years...

    Hi,
    Here is my Retro 1911 build I did years ago.

    Used a surplus Brazilian Army slide made by Colt with a Foster/ Caspian frame.

    Hand checkered 20 LPI, on the frame and the arched MSH.
    ...
  2. Replies
    7
    Views
    898

    Hi, Sort of related, explains some things...

    Hi,
    Sort of related, explains some things anyway!

    How to flat top and serrate your slide on a mill | 1911 Firearm Addicts
  3. Thread: China rising

    by seagiant
    Replies
    128
    Views
    6,888

    Hi, I highly doubt the CCP, could beat the...

    Hi,
    I highly doubt the CCP, could beat the Idiots, we now have in, the White House...

    For STUPID!!!
  4. Replies
    28
    Views
    2,632

    Hi, Thanks for the pics and the info,...

    Hi,
    Thanks for the pics and the info, probably something I should do to my 65 Series 1, but I'm to busy using it now!
  5. Hi, Fantastic, a labor of LOVE! Always...

    Hi,
    Fantastic, a labor of LOVE!

    Always liked that style of South Bend, usually the 13" Model!
  6. Replies
    7
    Views
    898

    Hi, Have you looked at Kunhausen's 1911...

    Hi,
    Have you looked at Kunhausen's 1911 Shop Manual Vol.2?
  7. Hi, Thanks, I found one!!!

    Hi,
    Thanks, I found one!!!
  8. delete.......................

    delete.......................
  9. Looking For Enco/Gamet Boring Head Operators Manual!

    Hi,
    Bought one of these but the instructions were not included.

    Does anyone know where I can get them for this head???
  10. Replies
    16
    Views
    648

    Hi, Just a shout out to John Evans for all...

    Hi,
    Just a shout out to John Evans for all the help!

    No, I have not fixed it, but know where the problem has to be, but I have a detent ball that will not come out of the shaft, so have to...
  11. Replies
    5
    Views
    500

    http://www.vintagemachinery.org/pubs/1617/3789.pdf

    http://www.vintagemachinery.org/pubs/1617/3789.pdf
  12. Hi, Very nice, thank you! Who's recoil...

    Hi,
    Very nice, thank you!

    Who's recoil lug are you using???
  13. Replies
    16
    Views
    648

    Hi, Ok, went back to the Schematic and I...

    Hi,
    Ok, went back to the Schematic and I see only a plunger and spring inside the "Block".

    I assume that is what you are freeing up when you pour in the lubricant and get most feeds back to...
  14. Replies
    16
    Views
    648

    Hi, Here is another thing, I saw no "Pin"...

    Hi,

    Here is another thing, I saw no "Pin" at the top of the block, just a hole?

    Could that be it, is something broken in the block?

    Just something I noticed and I even took a piece of...
  15. Replies
    16
    Views
    648

    Hi John, Thanks for all the help, I...

    Hi John,
    Thanks for all the help, I went in and removed the Overload Clutch Trip Lever #80...

    This allowed me to get to the hole at the top of the "Block",...

    It also allowed me to...
  16. Replies
    16
    Views
    648

    Hi, Thanks, I've done that already... I...

    Hi,
    Thanks, I've done that already...

    I have been all over the Internet looking for clues on this.

    Part # 97 is the trip plunger and is spring loaded, it is in the bottom of the "block"...
  17. Replies
    16
    Views
    648

    Hi, Thanks, I just took all that apart and...

    Hi,
    Thanks, I just took all that apart and cleaned it as stated above.

    It was grungy but cleaning did not make any difference.

    Played with the set screw up and down and makes no...
  18. Replies
    16
    Views
    648

    Hi, Thank you very much, I pulled the lever...

    Hi,
    Thank you very much, I pulled the lever at the bottom and #100 rod, cleaned everything up and still no go.

    That leaves the plunger and spring at the bottom of the block that's suppose to...
  19. Replies
    16
    Views
    648

    Hi, Well tried to take the handwheel clutch...

    Hi,
    Well tried to take the handwheel clutch collar #91 off but can not get the detent ball out!

    Have to get that off to get to the bottom of the "block" to check the parts in there?

    Well...
  20. Replies
    16
    Views
    648

    Hi, Finally found a schematic, I can put up...

    Hi,
    Finally found a schematic, I can put up so we can each see.

    On this print the parts in the bottom of #94 Cam Rod Sleeve. (what we called the block)...

    Is #96 and #97.

    Is there a...
  21. Replies
    16
    Views
    648

    Hi, Ok, on the Quill Housing parts schematic...

    Hi,
    Ok, on the Quill Housing parts schematic there is a spring loaded plunger in the bottom of the block...

    Parts # 120 and 121.

    That may be the problem, but will need to remove the block...
  22. Replies
    16
    Views
    648

    Hi, Thanks for the suggestion... I went...

    Hi,
    Thanks for the suggestion...

    I went and wet everything down and worked it and everything is free from what I can tell and moves as it should.

    Admittedly, I do not see the "pin" you...
  23. Replies
    16
    Views
    648

    1965 BP Series I Quill Downfeed Question!

    Hi,
    Looking to bore a hole and wanting to use the power downfeed for the last pass.

    The Quill downfeed works as long as you hold the lever back to feed, but...

    Will not "lock" and hold...
  24. Replies
    38
    Views
    3,283

    Hi, Looked awhile for my Lathe wanting...

    Hi,
    Looked awhile for my Lathe wanting American Iron...

    Really wanted a SB 13" but never saw one in my area for sale.

    A friend found a Clausing 12X36 out of State that he decided to sale...
  25. Hi, Thanks, I am going to make a mandrel,...

    Hi,
    Thanks, I am going to make a mandrel, for the receiver, so I can true the face.

    Do you have any pics of your bolt cutting set up???
Results 1 to 25 of 250
Page 1 of 10 1 2 3 4