Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: EmanuelGoldstein

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    22
    Views
    1,223

    You mean we went from over the rainbow to just...

    You mean we went from over the rainbow to just ... over ?


    https://youtu.be/duNQYWMna_4
  2. Replies
    3,601
    Views
    89,872

    Have you got a short circuit upstairs or...

    Have you got a short circuit upstairs or something ? Every single one of your little group was jumping on BB and calling him a coward for asking the stewardess to take care of the kid. So what's the...
  3. Replies
    3,601
    Views
    89,872

    Too bad. And if she spilled coffee in my lap on...

    Too bad. And if she spilled coffee in my lap on purpose she'd be out of a job.

    People can take their political correctness and put it where the sun doesn't shine.
  4. Replies
    3,601
    Views
    89,872

    Given the people flying these days, I'd say it...

    Given the people flying these days, I'd say it would be wiser to ask the stewardess.

    But more to the point, y'all were squealing in glee that BB didnt take on a ten year old and beat him to a...
  5. Replies
    3,601
    Views
    89,872

    Do you guys have a problem with short-term memory...

    Do you guys have a problem with short-term memory ? All of you were jumping up and down with glee, "Big B is a pussy ! He can't even stand up to a ten year old ! Ha ha ha !"

    Not that I give a shit...
  6. Replies
    22
    Views
    1,223

    That was Dorothy ! Alice was ten feet tall, she...

    That was Dorothy ! Alice was ten feet tall, she could just look over the curtain ...


    Ask and ye shall receive :D

    336336
  7. Replies
    553
    Views
    66,187

    Any place that has a yearly safety inspection or...

    Any place that has a yearly safety inspection or smog check could do it easily - just read the odometer.

    If they were nice they'd come up with a "voluntary" (like the IRS) plan where you could pay...
  8. Replies
    3,601
    Views
    89,872

    You would be if you came into my last shop ......

    You would be if you came into my last shop ... even grown men were scared to go past the wiring into the bathroom.

    I have witnesses :D

    Hey, if you don't touch it, it's not dangerous !
  9. Replies
    22
    Views
    1,223

    If it's just one tool, you could grind the taper...

    If it's just one tool, you could grind the taper down until the flange contacts. Might want to touch the flange to make sure it's square (then grind the taper some more :) maybe hit the flange first)...
  10. Replies
    3,601
    Views
    89,872

    Not if you watched the video and used your head...

    Not if you watched the video and used your head with the physical evidence. This is another case demonstrating that most eyewitnesses to trauma aren't that reliable ...

    In fact, if you read the...
  11. Replies
    64
    Views
    4,046

    Nope, they were real. The situation tho is that...

    Nope, they were real. The situation tho is that there is never perfect distribution of the load, at least on a midget. So one fastener is really doing all the work. When overloaded, one grade eight...
  12. Replies
    19
    Views
    1,467

    Had an 8" one of those. Didn't get to use it...

    Had an 8" one of those. Didn't get to use it often enough to eat up all the two-corners-usedup lathe inserts, but inserts for it were basically free, yippee !
  13. Replies
    553
    Views
    66,187

    Washington state does a cute trick ... they apply...

    Washington state does a cute trick ... they apply road taxes to marine fuel. The pumps are on docks with ten feet of water under them, you can't even get to them with a car or truck. And most boats...
  14. Replies
    3,601
    Views
    89,872

    Your knowledge of English is kind of...

    Your knowledge of English is kind of island-centric, aka parochial. In the US it's fine to run a drill press. Hell, you can run a bench grinder if you want.


    I've run seven, but that was...
  15. Cool ! Now all he needs are the values for the...

    Cool ! Now all he needs are the values for the speeds he wants and Bob's his uncle ! Lots of computer hobbyists can burn an eprom for him ... It'll drive the next owner of that machine crazy tho :D
  16. Replies
    3,601
    Views
    89,872

    Is it fun to give each other big wet sloppy...

    Is it fun to give each other big wet sloppy kisses over a subject neither one of you knows anything about ?
  17. They have parameters, like all controls. If...

    They have parameters, like all controls. If Dynapath would tell you what to change, it should be possible.

    Easier to just use G01 F RAPID/2 in place of G00 tho. If one is programming offline, can...
  18. Replies
    3,601
    Views
    89,872

    He talked okay but this ... ...

    He talked okay but this ...

    https://images.gawker.com/18k1hrq6z73hsjpg/c_fit,fl_progressive,q_80,w_636.jpg

    didn't give me a warm fuzzy feeling about how he'd handle the economy for average...
  19. Replies
    3,601
    Views
    89,872

    So who do you like, and what type of policies...

    So who do you like, and what type of policies would you like to see Congress pursue ?
  20. Over in China we usually go with a girl. Maybe...

    Over in China we usually go with a girl. Maybe not as efficient but a lot more pleasant to deal with.
  21. Yeah right. And the girls in leotards have...

    Yeah right. And the girls in leotards have nothing to do with it. Unh-hunh ....
  22. Replies
    3,601
    Views
    89,872

    I see that they don't teach counting in eastern...

    I see that they don't teach counting in eastern europe yet. Maybe next year ?
  23. The hurrieder go, the behinder I get ...

    The hurrieder go, the behinder I get ...
  24. Replies
    27
    Views
    3,811

    Thanks for the smile, it probably better be...

    Thanks for the smile, it probably better be "anyone" if you want a good result :)
  25. Replies
    19
    Views
    1,467

    For just general wackitaround milling I was happy...

    For just general wackitaround milling I was happy with a Sandvik that used tpg inserts. Those are so common and cheap that you can stock inserts for different materials easy. Nothing real special for...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4