Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: eKretz

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds; generated 41 minute(s) ago.

  1. Replies
    15
    Views
    2,244

    Got it wired up tonight. Got to set up the remote...

    Got it wired up tonight. Got to set up the remote keypad for the VFD still but it's ready to roll. Took a couple test cuts, everything seems fine.

    290032
  2. Replies
    1
    Views
    130

    I've always just tightened mine with no ill...

    I've always just tightened mine with no ill effect. Just tighten it appropriately, not like a gorilla...

    Just by the fact that you're asking first I think you'd have probably done that anyway....
  3. Replies
    5
    Views
    352

    Grazing incidence interferometry. You are sort of...

    Grazing incidence interferometry. You are sort of doing a very primitive "Home Shop Harry" version of it.
  4. Replies
    4
    Views
    236

    Not all of them are hydraulic. My Noga isn't. It...

    Not all of them are hydraulic. My Noga isn't. It uses a ramp ended rod to apply pressure against the ball joints to lock them. Can't really tell if that one is hydraulic or not, you'd have to take...
  5. Replies
    15
    Views
    2,244

    Yes they do offer regrinds for certain tapers (as...

    Yes they do offer regrinds for certain tapers (as you noted, BS#9 to R-8 may be the only one), but there's nothing wrong with this taper. QC30 is basically interchangeable with NMTB30, so pretty...
  6. Replies
    15
    Views
    2,244

    So I've just noticed that my Wells seems to have...

    So I've just noticed that my Wells seems to have a little different table than most. All the others I see are 3 T-slots, mine has 4 and the table measures about 12" x 46". Anyone else got a 4 T-slot...
  7. Thread: O.T.CBD oil

    by eKretz
    Replies
    44
    Views
    3,315

    I've had every procedure done that could be done....

    I've had every procedure done that could be done. As I noted earlier, I've been to the Cleveland Clinic to one of the "50 best spinal surgeons in the United States" with no help. As I hear from every...
  8. Replies
    7
    Views
    340

    Yeah, wood was not an ideal choice, to say the...

    Yeah, wood was not an ideal choice, to say the least. Hopefully you'll be able to work around it. Have you been flipping the lap end for end as suggested by Milland?
  9. Replies
    25
    Views
    910

    If I had a basement that nice I would have had a...

    If I had a basement that nice I would have had a float alarm that works off a battery. If the float goes up to a certain level it squawks with an annoying pitch until you pay it some attention. I...
  10. Replies
    8
    Views
    498

    Sounds to me like the seller has reasonable...

    Sounds to me like the seller has reasonable expectations. I would note that the machine is listed in the wrong forum though...
  11. Replies
    7
    Views
    340

    Got a photo of your setup? How are you making a...

    Got a photo of your setup? How are you making a hone with 500 grit diamonds? Do you really mean you made a lap? Need to get some better info before offering any advice.
  12. Bingo. The same could really be accomplished with...

    Bingo. The same could really be accomplished with the table alone. I'm still assuming that the O.P. is talking about a very large radius but he wasn't super clear about that.
  13. Thread: O.T.CBD oil

    by eKretz
    Replies
    44
    Views
    3,315

    There are different types and causes of back...

    There are different types and causes of back pain. Some can start elsewhere, but the disc-related ones are vicious. For those who haven't had the experience, imagine raw nerve pain like the worst...
  14. Thread: O.T.CBD oil

    by eKretz
    Replies
    44
    Views
    3,315

    Yeah, it may end up being a trade-off. But it is...

    Yeah, it may end up being a trade-off. But it is what it is...
  15. Thread: O.T.CBD oil

    by eKretz
    Replies
    44
    Views
    3,315

    Low back. Ruptured a disc. Got an artificial disc...

    Low back. Ruptured a disc. Got an artificial disc replacement, didn't do squat. Docs say most likely caused from all the unbalanced heavy lifting at my first job. Crane was tied up, I'd throw shit...
  16. Thread: O.T.CBD oil

    by eKretz
    Replies
    44
    Views
    3,315

    I tried the CBD gummies, didn't seem to do...

    I tried the CBD gummies, didn't seem to do anything for me. I am in about the same boat as Dualkit. I would like to have some active time rather than just lay down like a lump all the time. Ain't no...
  17. Oh for crying out loud....:nono: We need an...

    Oh for crying out loud....:nono:

    We need an anti-spambot bot army. :D
  18. Replies
    16
    Views
    1,152

    This is exactly how I've always done it on manual...

    This is exactly how I've always done it on manual machines without a facing type attachment or rotary table. Works a treat.
  19. Replies
    31
    Views
    1,834

    Just to save you all the headache: 289630 ...

    Just to save you all the headache:

    289630

    289631

    It looks like this is an old set, should be able to just unscrew the plug. Make sure you use a screwdriver that fits the slot tightly.
  20. Jaysus H. Cripes. Is there no way to stop these...

    Jaysus H. Cripes. Is there no way to stop these spam clowns?
  21. Replies
    34
    Views
    8,701

    That was a good deal. It was also already claimed...

    That was a good deal. It was also already claimed when both of you posted!
  22. I'm assuming you're talking about a radius...

    I'm assuming you're talking about a radius considerably outside the diameter of the table... Without simultaneous two axis movement you'd need to make up a large arm anchored elsewhere to hold the...
  23. Replies
    25
    Views
    18,151

    Nah. Not everything is crap, but a good portion...

    Nah. Not everything is crap, but a good portion of it still is. You can probably find a diamond in a dog's turd now and again too...

    I've tried several tools from Harbor Freight and plenty of...
  24. Replies
    34
    Views
    8,701

    Jim I haven't done any refurbishing to my own...

    Jim I haven't done any refurbishing to my own table other than getting the stuck worm disengagement loose. It was already in near new condition other than a little worn paint. Backlash on the worm is...
  25. Advance cross-slide rotary table manual and drawings

    Manual and some drawings for Advance cross-slide rotary table:

    Dropbox - Advance Rotary Table.zip - Simplify your life
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4