Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: henrya

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Why are you talking to such rude people? ...

    Why are you talking to such rude people?


    279452
  2. Wait, wait wait... Do nothing. ...

    Wait, wait wait...






    Do nothing.
    Just let it be.
  3. Replies
    27
    Views
    2,032

    I may need some too.

    I may need some too.
  4. Just a little thought experiment: If, if, if...

    Just a little thought experiment:

    If, if, if you had a contract on the building that you were sure would close and you had decided it really was time to move on and someone offered you $300,000...
  5. I might buy a few if anyone makes a small run. ...

    I might buy a few if anyone makes a small run.

    But, has anyone asked Aloris for some?
  6. Replies
    51
    Views
    3,524

    I wear a mask when I have any doubt about air...

    I wear a mask when I have any doubt about air quality. Same with eye and ear protection. If it might get loud or nasty I wear ‘em.
  7. Replies
    28
    Views
    1,919

    If the motor is in good operating condition, I...

    If the motor is in good operating condition, I suggest you look at a VFD. It will probably be the cheapest and easiest way to get the saw running.

    Then go here:...
  8. Replies
    17
    Views
    1,655

    Good to see you back, Stephen.

    Good to see you back, Stephen.
  9. I’d like to see the wanna-be-moderators stop...

    I’d like to see the wanna-be-moderators stop being so bitchy. Its pretty easy to direct a new poster to a different forum without insulting them. Then let the real mods do their thing.

    The...
  10. Replies
    16
    Views
    1,521

    Oiling of the chain and bar is a total loss...

    Oiling of the chain and bar is a total loss system. The oil comes into a port on the side of the bar and into the groove where the chain runs. From there it travels through the chain and is slung and...
  11. Replies
    23
    Views
    2,037

    If you can, take a picture of the motor’s...

    If you can, take a picture of the motor’s specification label and post it here. That will help those with the required knowledge know what you have.

    All I can add is that you will love having a...
  12. It might be that a shop that does architectural...

    It might be that a shop that does architectural scale powder coating will have a big enough oven. Think about railings and staircases that are powder coated.
  13. Thread: Led shop lights

    by henrya
    Replies
    36
    Views
    3,395

    If you are in a situation where judging color is...

    If you are in a situation where judging color is important, look at the spectral distribution of the light emitter you are selecting. This is a graph of the amounts of the range of wavelengths of...
  14. Thread: Boxford 280

    by henrya
    Replies
    5
    Views
    346

    There’s this: Boxford (and Clausing)...

    There’s this:

    Boxford (and Clausing) Industrial & Training Lathes 289, 280T, STS 10.20, TS 10.20, TF 10.20, TH 10.20, 330TR, TR.11.30, 330, 280, 280T, 330IS, 280IS, 250IS, 11.30, 11.20, 10.30 and...
  15. Thread: Morse taper 4.5

    by henrya
    Replies
    7
    Views
    708

    Try these folks: Home...

    Try these folks:

    Home

    JFK Precision.

    I have one of their collet adaptors and its very nicely made. You may have to call and ask for the adaptor you want.
  16. Replies
    25
    Views
    2,033

    One thing I like about the sockets is the...

    One thing I like about the sockets is the knurling at the top. It makes it easy to run a nut in or out by hand.
  17. Replies
    25
    Views
    2,033

    They actually do make a ratchet series called...

    They actually do make a ratchet series called Zyklop. I have one and its a nice tool.
  18. Replies
    25
    Views
    2,033

    I have three sets of Wera six point sockets. They...

    I have three sets of Wera six point sockets. They are very nice.
  19. Replies
    4
    Views
    979

    PM sent. More characters to make it work.

    PM sent.

    More characters to make it work.
  20. Replies
    29
    Views
    2,408

    Based on the above portion of the original post,...

    Based on the above portion of the original post, what do you really expect the epoxy to do? How heavily stressed is the part?

    I ask this because if you are really just looking for extra insurance,...
  21. Replies
    24
    Views
    2,224

    I have an older model of this series: ...

    I have an older model of this series:

    FinishPro HVLP | Graco Inc.

    Its been great for the 15 years or so I have owned it. The largest thing I have painted is the size of typical household doors....
  22. Corian or similar would make a great threshold....

    Corian or similar would make a great threshold. And those Schulter transitions look excellent.
  23. Get a real flooring guy over and have him trim...

    Get a real flooring guy over and have him trim the ends of the oak straight and then install a proper header where the two floors join. Finish all the wood to match. You may have to refinish the...
  24. Replies
    36
    Views
    2,428

    As anyone installed one of these units with the...

    As anyone installed one of these units with the lines inside the wall instead of running up the outside wall?

    I’m almost ready to put one in the new shop and in the wall would be so much cleaner...
  25. I often use a pencil or nail to make small angle...

    I often use a pencil or nail to make small angle adjustments. Put it between the work and the fence. Make a mark to repeat. Its like a sine bar.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4