Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gjkozy

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    663

    10K Grease fitting

    Browsing the book on SB rebuild, I came across the picture of a grease fitting that fits my spindle and back shaft, Thing is it's a 1/4-20 thread. I can find 1/4-28 fitting or 1/2-20 fitting,...
  2. Replies
    7
    Views
    1,609

    I saw the same thing and also wondered where one...

    I saw the same thing and also wondered where one could get one.
  3. Replies
    4
    Views
    889

    3C Collet Blocks

    Has anyone seen or heard of collet blocks made to fit 3C collets? How hard/easy would it be to machine a set?
  4. Replies
    434
    Views
    455,618

    Sticky: I saw a youtube video where a hand crank on the...

    I saw a youtube video where a hand crank on the lathe was used to help control cutting fine threads. I thought this was a great idea for a project and gave it a try. The handle was cold blued and the...
  5. I had a similar problem like you with a 10K that...

    I had a similar problem like you with a 10K that I had purchased. I would produce a finish something like a stack of checkers, even at the lowest feed rates and the shallowest of cut depths it would...
  6. Replies
    5
    Views
    1,284

    Thats an idea I haven't thought about.

    Thats an idea I haven't thought about.
  7. Replies
    5
    Views
    1,284

    I was thinking about that also, I just want to...

    I was thinking about that also, I just want to approach this in the correct way. When you look at the back of the dial, it almost looks like a relief was cut into it but worn down. That's what it...
  8. Replies
    791
    Views
    575,702

    Sticky: I have a cheapo cross slide vice for my...

    I have a cheapo cross slide vice for my drillpress, it's mounted on 1/2" flat steel with a nub welded on the bottom to quickly swap out with the drillpress table. Thing is, there was no good place to...
  9. Replies
    434
    Views
    455,618

    Sticky: Did you make the way mount? Sent from my...

    Did you make the way mount?

    Sent from my SM-N910P using Tapatalk
  10. Replies
    434
    Views
    455,618

    Sticky: When the lathe was purchased, it came with a...

    When the lathe was purchased, it came with a Craftsman milling attachment, since this is a 10K, it needed to be raised. It has a riser block with the 1 3/8" circular South Bend dovetail and a 1 1/4"...
  11. Replies
    434
    Views
    455,618

    Sticky: Made this lamp bracket for my 10K, the goose neck...

    Made this lamp bracket for my 10K, the goose neck lamp came off my grinder...bulb never lasted more than a few seconds. An after thought was adding a small shelf to put my oil pot on and a good flat...
  12. Replies
    434
    Views
    455,618

    Sticky: Much needed accessory! Great idea! Sent from...

    Much needed accessory! Great idea!

    Sent from my SM-N910P using Tapatalk
  13. Replies
    5
    Views
    1,284

    South Bend 10K Compound Dial Binds

    I recently purchased a 10K, it has the large dials. The problem is that when the compound crank us turned clockwise, inward, the dial binds and moves the crank while setting zero.

    It is difficult...
  14. Replies
    21
    Views
    8,652

    I also have a problem with 4140, bits cut good at...

    I also have a problem with 4140, bits cut good at first but do not last very long. Used brazed carbide and they lasted a bit longer. A search online says easily machined but find it a very hard...
  15. Replies
    43
    Views
    159,651

    Sticky: Hi All South Bend owners. Been reading posts and...

    Hi All South Bend owners. Been reading posts and gained tons of good info.

    I have a question, does any one have drawings, prints or just dimensions for the lead screws for a SB 9C? Mine are so...
  16. Thread: 5C OR 3C

    by gjkozy
    Replies
    8
    Views
    3,693

    Thank you. Since I already have the draw bar and...

    Thank you. Since I already have the draw bar and the accompanying pieces the 3C is what I will go with. These little tid bits of info I am picking up as I go forward.
  17. Thread: 5C OR 3C

    by gjkozy
    Replies
    8
    Views
    3,693

    I recently purchase a SB 9C and it came with one...

    I recently purchase a SB 9C and it came with one collet, nose piece and drawbar. The collet has Piviti 3SB stamped on it and it has 5/8" dia w/ 27 thread pitch on the end of the collet. My questions...
  18. Replies
    8
    Views
    15,057

    I had the same problem, purchased a new nut set...

    I had the same problem, purchased a new nut set but still had a gap of .026 between dial and handle depending which way I was cranking it.

    Since I only have one lathe I took the washer route, had...
  19. Replies
    22
    Views
    4,664

    Good thread, I too was considering this type of...

    Good thread, I too was considering this type of upgrade.
  20. Replies
    13
    Views
    4,284

    The gears you have listed is that a complete set?...

    The gears you have listed is that a complete set? I purchased a 9C and it came with a few gears, but, suspect it is not a full set as compared to pictures I have seen.
Results 1 to 20 of 21