Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: digger doug

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    4
    Views
    129

    ^ ^ ^ sounds like these: Locate A Material...

    ^ ^ ^ sounds like these:
    Locate A Material Handling Representative | MFG Tray
  2. "fire starter" they are....

    "fire starter" they are....
  3. Replies
    3
    Views
    267

    So there is a "tee" fitting in the sheet metal...

    So there is a "tee" fitting in the sheet metal box ?
  4. Replies
    12
    Views
    434

    ...and the fact that this one appears to have...

    ...and the fact that this one appears to have been stored at the bottom of a large pile of manure...is junk.

    alum. parts corroded, steel parts rusted, the gut's inside are probably frozen as well.
  5. Vacuum furnace.

    Vacuum furnace.
  6. Thread: G9972z

    by digger doug
    Replies
    3
    Views
    91

    Try over at "the zone" please. www....

    Try over at "the zone" please.

    www. seeandseezone.com (make the obvious changes, software here will not allow the proper linky to to written....:nutter:)
  7. Replies
    24
    Views
    1,075

    Thanks for the 'splainations. I don't use CI...

    Thanks for the 'splainations.

    I don't use CI as we have plenty of Iron in the water around here.
    So I make eggs every morning, use some olive oil in the pan, seems to be o.k.

    Bare fish (no...
  8. Replies
    24
    Views
    1,075

    What would be the difference in using a stainless...

    What would be the difference in using a stainless steel pan (some with a copper bottom bonded on the outside) rather than Cast iron ?
  9. Replies
    2
    Views
    452

    Nice video, but that's not much of a hill eh ? ...

    Nice video, but that's not much of a hill eh ?

    I was going to suggest adding bolt on angle iron grousers like seen on other TE's.

    However, seeing the location, and the "top heavy-ness" of said...
  10. Replies
    22
    Views
    1,243

    Main problem must be them leaving leetle...

    Main problem must be them leaving leetle cigarette butts around....:D

    Pitless adapter, and a sanitary cap, with the lead in wires sealed
    with sillycone, should allay any fears.
  11. What's wrong with BUYING a 20' conex box ?

    What's wrong with BUYING a 20' conex box ?
  12. Replies
    380
    Views
    22,429

    Your saying people with your spindle doo not...

    Your saying people with your spindle doo not replace the components like Bellvilles etc. ?

    And your not in control of the tool that engages YOUR spindle (funny how the customer pays for it the...
  13. Replies
    2
    Views
    264

    Oh...I see. So that's how it is with you....

    Oh...I see.

    So that's how it is with you....
  14. It's bad enough with regular coolants leading to...

    It's bad enough with regular coolants leading to dermatitis, and rusting problems, let alone tool wear and bad finishes.

    And now you want to play "backyard meth lab" with the coolant tank...
  15. Might say "J&L" on the front of the...

    Might say "J&L" on the front of the headstock......Or "W&S"
  16. Replies
    21
    Views
    1,142

    I dunno, I was a running a 48" one, table ran 90...

    I dunno, I was a running a 48" one, table ran 90 rpm max.,simple roughing job, and I had a helper.
    3 wheel barrow loads of chips a day, but it warnt easy.

    No sitting down on that job.

    Got...
  17. Replies
    22
    Views
    1,243

    sanitary cap ? Or expanding plug (with slot...

    sanitary cap ?

    Or expanding plug (with slot for the wires) ?
  18. Get your ass back over to the other side of the...

    Get your ass back over to the other side of the state, or I'll send you some snow....
  19. Replies
    21
    Views
    1,142

    "survive" ? You'll need room, powerline and a...

    "survive" ?

    You'll need room, powerline and a crane to service it.
    And at that, it has to earn it's keep.
    Put an employee on it, and bust y9ur butt all day to hold tolerances and
    get parts out...
  20. Replies
    21
    Views
    1,142

    Have you driven a Bullard lately ? They have...

    Have you driven a Bullard lately ?

    They have the option of two end turrets (as you see on the King) and the side head.

    Pinch turning or facing while boring while turning the O.D. etc.

    all...
  21. Replies
    7
    Views
    498

    you'll get more help at the hobby machinist sites.

    you'll get more help at the hobby machinist sites.
  22. Can you drill some tiny release holes to allow...

    Can you drill some tiny release holes to allow air in ?

    Or use some sacrificial plastic sheeting, one piece for each part.
  23. I'll bet your shop has a windsock out back for a...

    I'll bet your shop has a windsock out back for a bell jetranger….ugh
  24. Replies
    21
    Views
    1,142

    No side head, and I've driven one enough to wear...

    No side head, and I've driven one enough to wear me out, king 48"

    There are plenty of more modern ones available for just above scrap with pushbuttons for feed levers, digital readouts, etc.
    ...
  25. Replies
    124
    Views
    5,337

    A guessing game in which there is no incentive to...

    A guessing game in which there is no incentive to make the process better.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4