Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Triaged

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    283

    Always model at nominal! I've seen minus/minus...

    Always model at nominal! I've seen minus/minus tolerances screwed up more times than limit dimensions.
  2. Replies
    17
    Views
    1,098

    It's Verizon math! VerizonMath: Verizon doesn't...

    It's Verizon math!
    VerizonMath: Verizon doesn't know Dollars from Cents
  3. Replies
    15
    Views
    1,354

    UN imperial screw thread calculator...

    UN imperial screw thread calculator
  4. Replies
    9
    Views
    1,180

    Try one of the Norton TG wheels talked up by...

    Try one of the Norton TG wheels talked up by Norton in this cleverly disguised coolant test and let us know how it works.

    Critical Cooling for Gear Grinding Success | Norton Abrasives
  5. I have seen adds for these but never tried them....

    I have seen adds for these but never tried them.

    XEBEC Brush™ Surface | XEBEC TECHNOLOGY CO.,LTD.
  6. ATTACHMENTS + OTHER TOOLS | FOREDOM...

    ATTACHMENTS + OTHER TOOLS | FOREDOM should be under $500 depending on options. You would have to take the guard off to get 3" but you likely don't have one now.
  7. Replies
    23
    Views
    2,033

    My comment wasn't intended to be demeaning....

    My comment wasn't intended to be demeaning. Century Spring has been around for quite a while, has a huge catalog, and reasonable prices. In my experience modified springs don't provide reasonable...
  8. Replies
    23
    Views
    2,033

    If century spring doesn't have what you need,...

    If century spring doesn't have what you need, redesign what you are making.
  9. Replies
    24
    Views
    2,909

    What kind of carbide? For a cutting tool? Most in...

    What kind of carbide? For a cutting tool? Most in that size range will be forging grades. Circular form tool blank?
  10. Replies
    47
    Views
    4,114

    You might want to check out the IC608. It is the...

    You might want to check out the IC608. It is the same 08 substrate as IC808 but with the kitchen sink thrown into the coating...AlTiCrSiN.
  11. Replies
    4
    Views
    736

    I'd likely do the bore first then do the threads...

    I'd likely do the bore first then do the threads with a thread mill.
  12. Replies
    22
    Views
    1,308

    Tip or insert? SumoCham? Which tool exactly are...

    Tip or insert? SumoCham? Which tool exactly are you using for the first material? Could you use the same tool all the way through just changing speed and feed? I bet a SumoCham ICP would make it....
  13. Replies
    22
    Views
    1,308

    Never messed with stuff like that but I wouldn't...

    Never messed with stuff like that but I wouldn't use 2 brands for the same hole. The reps will just blame the other brand (likely both rightfully so). Pick one brand, have the rep come in, and tell...
  14. Replies
    8
    Views
    838

    Flat mild steel part. Laser or punch?...

    Flat mild steel part. Laser or punch?
  15. Replies
    3
    Views
    611

    Do you have it on during the whole cycle? Pick...

    Do you have it on during the whole cycle? Pick one operation or tool to have it on and off the rest of the time. The chips need some time to drip dry before going in the bin.
  16. Replies
    22
    Views
    1,811

    Id look into some of the old "plastics" like...

    Id look into some of the old "plastics" like paper micarta or maybe Bakelite.
  17. You don't think you could correlate the double...

    You don't think you could correlate the double shear in a standard fixture to the single shear in your application? It might not exactly be double shear x 3 / 2 but there is likely a coefficient very...
  18. I think the requirement for a special shear...

    I think the requirement for a special shear fixture is what the problem is. There are already 2 standard fastener shear types out there. I'd suggest double shear per NASM1312-13. There are many test...
  19. Replies
    19
    Views
    1,602

    Give these guys a try. It's been a long time...

    Give these guys a try. It's been a long time since I used them but they never did me wrong.

    Elite Laser Services - Elite Laser Cutting
  20. Replies
    19
    Views
    1,602

    You can get 4130 in .080" and .090". That is a...

    You can get 4130 in .080" and .090". That is a material many laser cutters should stock in the normalized condition. At least here in SoCal with all the motorsport stuff it's common. You can heat if...
  21. Replies
    80
    Views
    21,455

    What is the Brix to % multiplier? What does it...

    What is the Brix to % multiplier? What does it have to be for a coolant to be considered clear?
  22. Thread: ABS cutting

    by Triaged
    Replies
    5
    Views
    885

    The best way to "cut" ABS is to injection-mold it.

    The best way to "cut" ABS is to injection-mold it.
  23. Replies
    17
    Views
    1,342

    Wow! I'm bad at math sometimes!

    Wow! I'm bad at math sometimes!
  24. Replies
    17
    Views
    1,342

    That's a thin wall and not a low tool pressure...

    That's a thin wall and not a low tool pressure insert. It's a negative insert, big radius for the DOC, and the M of the chip breaker is for medium machining which means a honed edge not sharp. I'd...
  25. Thread: Parting off

    by Triaged
    Replies
    4
    Views
    646

    Are you using a sub-spindle to pick it off? If...

    Are you using a sub-spindle to pick it off? If not you will just move the location of the burr.
Results 1 to 25 of 149
Page 1 of 6 1 2 3 4