Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: claytonbraga

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    1,308

    Hello Agieman, Unfortunatelly I had bad news...

    Hello Agieman,

    Unfortunatelly I had bad news for me..... my machine started to present the same behavior again, (The can cut during 5 -10 minutes and then the wire touch the workpiece and not...
  2. Replies
    17
    Views
    1,308

    No, I just put additional cables, I keep all the...

    No, I just put additional cables, I keep all the original ones because I'm not sure if my cables can work well in high frequency.

    In resume, I put 4 new cables in parallel with the original...
  3. Replies
    17
    Views
    1,308

    Hello Agieman, Thanks again for your support,...

    Hello Agieman,

    Thanks again for your support, I spend a long time to answer because I was perfoming some test on the machine.

    I performed a total clean process on water tank (I was suspecting...
  4. Replies
    17
    Views
    1,308

    UPDATE: I made a double check on all cables on...

    UPDATE:
    I made a double check on all cables on upper and lower arms and I discovered more 3 cables damaged (+- UFS and FM). now all the erros disappeared, :D.

    But unfortunatelly my machine still...
  5. Replies
    17
    Views
    1,308

    I checked the black wheel (conofil wire brake)I...

    I checked the black wheel (conofil wire brake)I stoped it manually and the wire slip during 1 or 2 seconds and then broke between the heads. Considering this I replaced one of the wire belts for a...
  6. Replies
    17
    Views
    1,308

    I discovered one cable damaged on lower arm,...

    I discovered one cable damaged on lower arm, after the repair of this cable the short circuit error disapeared,:D but now the machine are presenting a wire broken or not threaded in, error 420.

    I...
  7. Replies
    17
    Views
    1,308

    I discovered one cable damaged on lower arm,...

    I discovered one cable damaged on lower arm, after the repair of this cable the short circuit error disapeared,:D (picture attached) but now the machine are presenting a wire broken or not threaded...
  8. Replies
    17
    Views
    1,308

    Hello Agieman, Probably I will never use the...

    Hello Agieman,

    Probably I will never use the SF module because for the job that I will perform with this machine the rugosity is not important, probably I will use only the mode 5 and 6.

    Sorry...
  9. Replies
    17
    Views
    1,308

    Hello Agieman, Thanks a lot for your answer,...

    Hello Agieman,

    Thanks a lot for your answer, :)

    What is the gap boxes? is this this box on picture below? I disassembled this weekend the lower arm to clean everything and I noticed that this...
  10. Replies
    17
    Views
    1,308

    Hello, sorry to ask again but someone have an...

    Hello, sorry to ask again but someone have an idea what I can test to try to solve the issue??

    I really in trouble with this problem!!!
  11. Replies
    17
    Views
    1,308

    Agie 200D with strange behavior !!!

    Hello Everybody, My name is Clayton and I'm from Brazil, I have a Agie 200D +SF and my machine started to present a strange behavior, when I try to cut using Mode 6 the machine present short circuit...
  12. Replies
    12
    Views
    2,081

    Agie parts

    Hello Larry,

    I have one Agie 200D do you have any parts commom between these to models (AC100 to AC200D) my machine is working but still need to replace some parts.

    If you have pictures or...
  13. Replies
    5
    Views
    3,217

    I need this manual set too, can you help me and...

    I need this manual set too, can you help me and send it to [email protected]?
  14. do you still have parts from Robofil 200? what is...

    do you still have parts from Robofil 200? what is the list of parts and price?
  15. Replies
    5
    Views
    3,217

    Hello smr123, I need the same manual set for...

    Hello smr123, I need the same manual set for robofil 200, can you help me and send for the email [email protected] thank's a lot for you help.
Results 1 to 15 of 15