Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cg285

Page 1 of 45 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    20
    Views
    947

    what my PT uses on scars (incisions)

    what my PT uses on scars (incisions)
  2. yep. been there

    yep. been there
  3. not knowing the valve stem dia but possibly an...

    not knowing the valve stem dia but possibly an easy way would be to make the cast guides to od then bore to accept off the shelf guides from such places as goodson.com
  4. same, i was going to use alternator as an example...

    same, i was going to use alternator as an example (or a/c compressor clutch coil)
  5. i think in this example the term would be "anal"...

    i think in this example the term would be "anal" haha
  6. Replies
    54
    Views
    3,494

    appears like a reflex problem

    appears like a reflex problem
  7. +1 i have found it somewhat hard to machine...

    +1
    i have found it somewhat hard to machine afterwards.

    i have always been able to get the rods and flux at the local welding supply
  8. different area but bone spurs in my elbow turned...

    different area but bone spurs in my elbow turned into lumps which turned into bigger lumps until less than 30 degree range of motion. surgery has range of motion mostly all back but after 3 months...
  9. Replies
    47
    Views
    2,899

    not the same subject as normal train traffic but...

    not the same subject as normal train traffic but i had a spur at my shop that hadn't been used in years. i needed to bring down 240 tons of steel molds. they were scheduled to be delivered one night...
  10. Replies
    47
    Views
    2,899

    never that but as a kid i rented a bay in a...

    never that but as a kid i rented a bay in a storage facility. 110v only back then. neighbor had power pole put in and 220 service (before 240) put in to power refrigeration. i needed to weld some...
  11. i've done that more than once but never got a...

    i've done that more than once but never got a good arc so it was apparent right away
  12. Replies
    24
    Views
    1,914

    don't know what materials you intend to spray but...

    don't know what materials you intend to spray but for the most part paints are designed to be mixed to an exact ratio regardless of what equipment you are using.
  13. asphalt millings in 3 different locations. all...

    asphalt millings in 3 different locations. all with class A motorhomes sitting on it and with tractor trailer traffic. no noticeable divots under the motorhomes. sand base. if someone did get divots...
  14. Thread: Memorial Section

    by cg285
    Replies
    42
    Views
    2,977

    one problem i see. how are we to notify PM when...

    one problem i see. how are we to notify PM when we're gone?
  15. i questioned how they could do that but that's...

    i questioned how they could do that but that's how the zoning changed. was time to get out
    maybe going vertical?
  16. actually the fuel pump will only have power for...

    actually the fuel pump will only have power for about 3 seconds without the engine running.

    no fuel filter persea
    fuel pressure gauge would be a helpful visual
    fuse check
    swap pump relay with...
  17. year, model and/or vin would be helpful

    year, model and/or vin would be helpful
  18. it's 4k so double that and see if it flies.

    it's 4k so double that and see if it flies.
  19. my location - florida - it was not required (just...

    my location - florida - it was not required (just the handicap bullshit). it was suggested by my brother the builder
  20. i built a home in the middle of nowhere in 2007....

    i built a home in the middle of nowhere in 2007. lightning protection for house and 3k' shop was 3500. on another note - sadly it is not in the middle of nowhere any more in fact it, and everything...
  21. Replies
    11
    Views
    1,226

    no knowledge about wall structure but for a...

    no knowledge about wall structure but for a "floor" comparison:

    75x50 6" deep 24x24 footers, footers under 2 lifts (6 footers don't remember size) rebar,wire, fiber
    17k inc material 3 years ago.
  22. Replies
    26
    Views
    3,641

    my bride's brother quit his job at the university...

    my bride's brother quit his job at the university to get into construction work. he is now short three fingers due to free handing cutting something on a table saw (from the back side)
  23. Replies
    20
    Views
    1,309

    https://www.ebay.com/sch/i.html?_from=R40&_nkw=the...

    https://www.ebay.com/sch/i.html?_from=R40&_nkw=thermostat+3800884&_sacat=0&_sop=15
    from 39.99 to 76.28 took just seconds to find
  24. Replies
    22
    Views
    3,891

    i used it for many years but got rid of the hot...

    i used it for many years but got rid of the hot tank in 2005 and haven't used it since. used it on engine blocks, heads, etc
  25. might be an issue getting one shipped. i have...

    might be an issue getting one shipped. i have fuel tanks made and sell online. i get shipping grief calling them new, unused, never had gas in fuel tanks. so now i call them water tanks
Results 1 to 25 of 1121
Page 1 of 45 1 2 3 4